Product Information
Description:
This is a Genuine OEM Makita replacement part, this part is sold individually. It is part of the blade clamping system for the specific Makita Reciprocating Saws. Only use the properly sized Hex Tool to tighten and loosen this bolt. Make sure the bolt is tight but not overtightened. |
Frequently Purchased With
Compatibility
This part is compatible with the following machines:
Products Compatibility
This item works with the following types of products:
- • Reciprocating Saw
- • Saw
Questions & Answers for Hex Head Bolt
No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
5 of 6 people found this instruction helpful
Tool Type:
Reciprocating Saw
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
, allen wrench
Blade holder wore out
Just remove old worn out blade clamp with allen wrench and slip new one on.
saved me $100.00 bucks on new saw
saved me $100.00 bucks on new saw
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Circular Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Wrench Set, allen wrench
shoe self destructed
replaced shoe. replaced insulation cover
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Reciprocating Saw
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver
Saw motor ran but the blade didn't move.
1. Disassembled front 3rd and determined that the slider shift was broken.
2. Replaced slider shaft, needle bearing 708, and blade clamp.
3. Applied bearing grease where needed.
4. Replaced insulation cover.
2. Replaced slider shaft, needle bearing 708, and blade clamp.
3. Applied bearing grease where needed.
4. Replaced insulation cover.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Reciprocating Saw
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Nutdriver
Worn blade clamp
Just remove the worn parts from the end of the shaft and replace them with the new parts.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Reciprocating Saw
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
, allen wrenches
The blade clamp broke on my Makita reciprocating saw
Not a big deal take the broken part off and put the new part on the shaft. You will need a set of metric allen wrenches
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
5 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
5
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
Exact part
Correct item and fast shipping. Will do business again.
Guest -
October 25, 2020
Verified Purchase
The parts that I have requested work very fine.
I like the way you send me my parts for my swivel saw. Thank you, Jefferson
Guest -
October 15, 2020
Verified Purchase
Exactly the part I needed to repair my tool.
Bolt fit perfectly and my saw is back in service.
Guest -
August 19, 2019
Verified Purchase
exact fit good job
my Makita sawsall is back together with correct parts ordered, returning customer same satisfaction Thanks
Guest -
July 3, 2019
Verified Purchase
Worked as expected
I'm so happy that in a throw-away world, companies like yours still exist. My 30 yr old Makita sawsall is working like new!
Guest -
May 14, 2019
Verified Purchase
Verified Purchase
eReplacementParts Team
< PREV
- 1
Product Information