This item is a genuine Ryobi replacement part that has been sourced from the original manufacturer to be used with backpack blowers. The gasket is used to seal the connection between the carburetor and the heat dam. The gasket also provides insulation around the carburetor. This item is available as an individual replacement part.
Gasket 562927001
OEM part for: Ryobi
Part Number: 562927001
Jump To:
Frequently Purchased Together ?
Compatibility
This part will fit the following 2 machines
Ryobi
This item works with the following types of products:
- Blower Parts
- Vacuum Parts
Customer Part Reviews ?
- 1
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Gasket
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Would not throttle up
Tool Type
Blower
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
Remove the fuel lines and throttle from the carburetor
Remove the two screws securing the air box base and the carburetor
Remove the old carburetor and gasket and clean area
Install the new carburetor and gasket and air box base
Connect the throttle and fuel lines
Install the new filter
Install the rest of the air filter parts
Carb gasket torn
Tool Type
Blower
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
Parts Used
Remove gasket
Replace gasket
Replace carburetor
Poor combustion
Tool Type
Blower
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver, Socket set, Wrench Set
.broken rope
Tool Type
Blower
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Socket set, Wrench Set
Parts Used
Bogged down at high rpm's
Tool Type
Blower
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Torx bit
Parts Used
-Remove carburetor mounting screws
-Remove carburetor and clean all remaining gasket material from intake manifold surface
-Fit new carburetor gasket to intake manifold, being careful to line up any and all holes properly
-Tighten carburetor mounting screws to intake manifold
-Reinstall air filter housing
-Prime, choke, and start engine
-Allow engine to warm up, then adjust low speed and high-speed mixture screws (this will require a special mixture adjusting screwdriver to turn the "D" shaped screw heads)
Didnt keep getting fuel,
Tool Type
Blower
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver, Pliers, Nutdriver
Parts Used
Removed air cleaner holder also carburetor cover
Removed fuel lines,and unhooked throttle cable, removed carburetor
Remove gasket,
Reinstalled gasket, carburetor and replace other parts, adjusted carburetor
And run as good a new
Blower would idle, but stall on accelaration.
Tool Type
Blower
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Socket set, Nutdriver
Parts Used
Unit would start but wouldn’t run at full speed.
Tool Type
Blower
Difficulty
Medium
Time
15-30 minutes
Tools Used
Nutdriver
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.