eReplacementParts.com
866-322-9842
Poulan Parts
Repair Parts Home  Lawn Equipment Parts  Poulan Parts  530071750 Gasket Kit

Gasket Kit

Part Number: 530071750
PoulanWeed EaterHusqvarna
Availability: 25+ in stock
Price: $10.25
Quantity:
Order within the next 14 hours
and your part ships today!
Product Information
Manufacturer: Poulan, Weed Eater, Husqvarna
Product Number: 530071750
Classification: Part
Weight: 0.09 lbs.
Shipping: Ships Worldwide
Specifications
  • 25cc
Description:
This is a Manufacturer Approved replacement kit used on a variety of Gas Trimmers/Pruners. This gasket set includes the major gaskets to replace when rebuilding the engine. Its purpose is to make an air tight seal so that no air/oil leakage occurs. Over time gaskets tend to deteriorate and will need to be replaced. Gaskets in this kit are made out of Composite Material and O-Rings are made out of Rubber.
Compatibility

This part is compatible with the following machines:

Poulan
Weed Eater
Husqvarna

Products Compatibility

This item works with the following types of products:

  • • Edger
  • • Pruner
  • • Trimmer
Questions & Answers

No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
9 of 10 people found this instruction helpful
Tool Type:
Trimmer
Parts Used:
Air Filter Foam - 530036575
Spark Plug - 952030249
Gasket Kit - 530071750
Carburetor Assembly - 530071811
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
, Allen Wrench
Would not run with choke in off position.
These are the steps i used... Remove fuel lines from carburetor note position of each. Open up cover of air box. Remove air filter. Remove two screws with Allen wrench. Remove air box. Slighty remove carburetor and unhook throttle cable linkage noting the way it hooks up. Remove carburetor. Make sure old gasket doesn't stick to carburetor adapter. Remove two screws and remove carburetor adapter. Take carburetor adapter, air box, and air box cover and clean with toothbrush and dishwash liquid. Dry thoroughly. Take a q-tip dip in cleaner and clean around cylinder where adapter fits. Push screws through carburetor adapter and put new gasket on screws pushing it on adapter so it lines up perfectly. Tighten adapter on cylinder. Push screws through air box, new carburetor, and place new gasket on screws against carburetor so gasket lines up perfectly. Install throttle linkage cable to carburetor. Tighten screws back down. Clean air filter, or replace then install air box cover. Hook fuel lines back up in proper position. Always, ALWAYS use non-ethanol gas in your weed eater with proper oil mixture. My Poulan weed eater is 13 years old and this is the first time I habe replaced anything on it.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
4 of 4 people found this instruction helpful
Tool Type:
Trimmer
Parts Used:
Cylinder - 530012541
Gasket Kit - 530071750
Air Box - 580731001
Kit- Piston - 530071833
Repair Difficulty:
Medium
Time Spent Repairing:
More than 2 hours
Tools Used:
Pliers
Hard starting, lack of power, adjusting carburetor made no difference.
1. Removed shrouds
2. Removed engine from trimmer mount
3. Removed cylinder from block
4. Removed retaining rings from piston, pushed piston pin out, removed piston.
5. Reversed above procedure installing new piston
6. Installed piston ring, oiled piston and ring, then slid cylinder over piston
7. Bolt cylinder down
8. Remove accessories from first cylinder and install on new cylinder
9. Reinstall engine on trimmer mount, reinstall shrouds
10. Start engine and adjust carburetor
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Pruner
Parts Used:
Gasket Kit - 530071750
Carburetor Assembly - 530071811
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
, Allen head socket
Removed the two gas lines from the carburetor removed the two screws holding it in place under the air cleaner unhook the throttle cable.
Used new gasket and carburetor from ereplacementparts in reverse order. It was simple primed the carburetor pulled the starter three times back in business
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Trimmer
Parts Used:
Gasket Kit - 530071750
Adapter - Carb - 530057547
Carburetor Assembly - 530071811
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Torx
Bad carb and cracked carb adapter
Removed air filter assembly
Removed carb bolts
Replaced carb adapter o-ring
Reinstalled in reverse order
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Trimmer
Parts Used:
Gasket Kit - 530071750
Carburetor Assembly - 530071822
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers, Wrench Set
Line trimmer would not start
Removed to air filter.
Removed the carburetor
Installed the new carburetor.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Trimmer
Parts Used:
Gasket Kit - 530071750
Carburetor Assembly - 530071822
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Screwdriver with hex head and hex wrench
Replaced carb and gasket.
Pretty straight forward if you have the proper tools and a mechanical aptitude. Removed fuel lines, air filter and 2 hex bolts that held the defective carb. Replaced with new parts and put back together. Filled the tank with fresh gas
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Hedge Trimmer
Parts Used:
Gasket Kit - 530071750
Screw - 530016429
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Bit for the screws.
Gasjet was in bad shape
Put the new gasket on and threaded the new screws in because the old ones were bad.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 5 people found this instruction helpful
Tool Type:
Trimmer
Parts Used:
Fuel Cap With Retainer - 530014347
Gasket Kit - 530071750
Foam Air Filter - 530057781
Carburetor Assembly - 577135902
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Socket set, Nutdriver
Weed eater trimmer will not start.
1. Replaced the carburetor assembly.
2. Replaced air filter foam.
3. Replaced spark plug.
4. Replaced fuel tank cap.
5. Waiting for the fuel line hoses and fuel filter. (found hoses deteriated)
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Hedge Trimmer
Parts Used:
Gasket Kit - 530071750
Purge Bulb - 530058709
Repair Difficulty:
Medium
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, hex wrench
Hedge trimmer bade dull, needed replacement. Carb leaking fuel.
Removed and replaced trimmer blade. Removed carb, disassembled, cleaned and rebuilt with new parts/gaskets etc.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 2 people found this instruction helpful
Tool Type:
Trimmer
Parts Used:
Air Filter Foam - 530036575
Gasket Kit - 530071750
Screw - 530016429
Fuel Filter - 530095646
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Hex key
Needed new carburator
1. Removed old carb
2. Put on new gasket on new carb
3. Installed new air filter insert
4. Installed new fuel pick up
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Discussion
Discussion for Gasket Kit - ( 530071750 )
Discussion is closed. To ask our experts a question about a part, use the Q&A feature.
Question: Gasket Kit

1484564

I purchased this kit because I need a replacement gasket for the carborator but I do noe see the part I need in the package. Is there another gasket kit just for the carborator.
That carburetor gasket....part no. 530071750 is a fit for the Weedeater FL20 machine. What MODEL machine do you have? Do a search on here for your exact model again possibly and check the diagram/parts listing for it to find the correct gasket.

http://www.ereplacementparts.com/images/poulan/FL20_Type_1.pdf
Question: Featherlite Weedeater

renea

I don't see where to order the gasket that goes between the carburetor adapter&the carburetor..have I overlooked it?
WJA
Hello renea,

If the model number is a Weed Eater Featherlite SST 25. The gasket you are looking for is included in the gasket kit part number, 530071750. Before ordering the kit, you may want to double check the model number. There are quite a few different models of the Featherlite made by Weed Eater and they all don't use the same parts.

-WJA
I am about to order a replacement carb for my Weedeater Featherlite but have the same problem. The gasket kit only shows one gasket that looks like the ones on my trimmer. It is a model FX26S. Would I have to order another part or will the new carb come with the gaskets?
WJA
Hello 1181904,

The carburetor does not come with the gasket. To get the carburetor gasket you would also have to order part number 530071750 gasket kit.

-WJA
Reviews
4
Average Rating (out of 5):
1 Reviews
Click to filter by ratings:
5 stars
0
4 stars
1
3 stars
0
2 stars
0
1 stars
0
  • Highest Rating
  • Most Recent
< PREV
  • 1
NEXT >
  • Gasquets
    They fit good easy insulation
    Guest - July 1, 2019 Verified Purchase
    Verified Purchase
    eReplacementParts Team
    • Highest Rating
    • Most Recent
    < PREV
    • 1
    NEXT >
    Product Information
    Manufacturer: Poulan, Weed Eater, Husqvarna
    Product Number: 530071750
    Classification: Part
    Weight: 0.09 lbs.
    Shipping: Ships Worldwide
    eReplacementParts.com
    7036 South High Tech Dr.
    Midvale, UT 84047
    visa mastercard discover american express PayPal

    fancyboxy