fancyboxy
eReplacementParts.com
866-322-9842
Craftsman Parts
Repair Parts Home  Power Tool Parts  Craftsman Parts  530069247 Fuel Line (25-Inch)

Fuel Line (25-Inch)

Part Number: 530069247
Craftsman
Availability: 25+ in stock
Price: $6.93
Quantity:
Ships within 1 business day

*This part replaces obsolete part #: 21054, 21053 and 530071404.

Product Information
Manufacturer: Craftsman
Product Number: 530069247
Classification: Part
Weight: 0.01 lbs.
Shipping: Ships Worldwide
Description:
This is a Genuine Manufacturer Sourced replacement part designed for Craftsman Gas Chainsaws. This part carries fuel from the tank to the carburetor and from the primer bulb to the fuel system. After time the fuel lines will become brittle and crack so they would need to be replaced.
Compatibility

This part is compatible with the following machines:

Craftsman

Products Compatibility

This item works with the following types of products:

  • • Chain Saw
  • • Saw
Questions & Answers

what are the measurements of fuel lines 530069216 & 530069216
rory for model number 358.794741
Hello Rory, Thank you for the question. The length of the 530069216 fuel line is 2 feet.Thank you for your inquiry, good luck with this repair!
I need both sizes of fuel hoses. Do parts #6: 530069216 and #7: 530069216 cover both diameters?
Brad for model number 358.791580 Craftsman Trimmer
Hello Brad, Thank you for the question. Yes, the 530069216 and 530069216 are both size fuel lines. Thank you for your inquiry, good luck with this repair!
What is the inside and outside diameter of this fuel line?
Tyler mcbride for model number 358350601
Hello Tyler, thank you for your question. This replacement for your model has an outer diameter of 0.14" and an inner diameter of 0.08".
Repair Instructions: Submitted by Customers Like You
21 of 25 people found this instruction helpful
Tool Type:
Chain Saw
Parts Used:
Fuel Filter - 530095646
Fuel Line (25-Inch) - 530069247
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers
Fuel line in gas tank was disintigrated, chain saw would not start
To get the new fuel line in the tank you must bevel the end, about an inch, with a very sharp knife. Push this end through the hole in the gas tank then reach in with a long, long nose plier and pull the end of the fuel line slightly out of the filler neck, cut off the bevel, install the filter then pull it back so the fuel filter rests on the tank bottom.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
15 of 16 people found this instruction helpful
Tool Type:
Chain Saw
Parts Used:
Fuel Line (25-Inch) - 530069247
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Pliers
Replaced fuel line
Remove the fuel from the fuel tank. Bend a hook in a length of wire and fish the fuel filter out of the fuel tank. Remove the fuel line from the primer bulb. Then remove the fuel line from the fuel tank. Install the new fuel line on the primer bulb. Then on the other end of the fuel line cut it diagonally, then and put some oil on the end of it and press it into the tank. If you have some hemostats or long needle nose pliers, take hold of the hose that's inside the tank and pull it out of the tank. Measure how much you will need to have the fuel filter sit properly in the tank , then cut it off straight and place the hose on the fuel filter. Put the filter in the tank. Put the fuel in the tank, and you should be ready to do some cutting.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
9 of 11 people found this instruction helpful
Tool Type:
Chain Saw
Parts Used:
Fuel Line - 530069216
Primer Bulb - 530071835
Fuel Filter - 530095646
Fuel Line (25-Inch) - 530069247
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers, Socket set, Scissors/Knife
Fuel Lines aged and brittle
1) Removed top cover
2) Removed Spark Plug
3) Removed Side Cover
4) Removed Helper Handle
5) Drained Fuel Tank
6) Recover Fuel Filter
7) Took Pictures of Carburetor and Fuel Line Routing
8) Removed Fuel Lines
9) Removed Primer Bulb
10) Removed Carburetor
11) Fish new Lines into Fuel Tank, cut to size
Re-install parts
Did you find this story helpful?
Thanks for voting and helping fellow customers!
6 of 8 people found this instruction helpful
Tool Type:
Blower
Parts Used:
Fuel Line - 530069216
Fuel Line (25-Inch) - 530069247
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Knife
Fuel line to primer bulb brittle and broken
1. Removed plastic cover
2. Fished old fuel line from fuel tank
3. Cut new line same length as old line
4. Pulled old line from primer bulb and fuel filter, and pushed on new line
5. Put line with fuel filter into fuel tank and reinstalled plastic cover
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Trimmer
Parts Used:
Fuel Filter - 530095646
Fuel Line (25-Inch) - 530069247
Carburetor Gasket - 530019156
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers
Card would not run. Gas was not entering the carb. Conclusion - fuel filter was clogged.
1. Removed air filter
2. Removed gas line & throttle cable
3. Remove carb.
4. Push fuel line further into tank until you can grab the old fuel filter with a pliers.
5. Pull out old filter & gas line through the filler opening.
6. Cut a sharp angle on the fuel line and push into the tank.
7. Grab with the pliers through filler hole, pull line out, cut end straight across & add on the filter.
8. Pull line so the filter goes into the tank and can flop around.
9. Cut gas line so it fits onto carb.
10. Reinstall carb & throttle & air filter.
11. Trimmer should now work. Mine did.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Chain Saw
Parts Used:
Fuel Line - 530069216
Gasket Repair Kit - 530069844
Fuel Line (25-Inch) - 530069247
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Nutdriver, knife
engine would not start
1. Replaced the internal gaskets and external fuel lines on the carburetor
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Chain Saw
Parts Used:
Fuel Line - 530069216
Fuel Line (25-Inch) - 530069247
Repair Difficulty:
Medium
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, Pliers, Tooth pick
It would start,then would smother out.
Took top of chainsaw off,gas cap off.Old lines brittle,took them off.Cut new lines to length.Put back together,filled with new fuel,primed,started up.Runs like a new one.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Chain Saw
Parts Used:
Fuel Line - 530069216
Fuel Filter - 530095646
Fuel Line (25-Inch) - 530069247
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers, Socket set
Fuel lines aged out and needed replacement; broke apart.
Replaced the fuel lines and filter
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Chain Saw
Parts Used:
Fuel Line (25-Inch) - 530069247
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers, Socket set, Nutdriver, Forceps
fuel line in chainsaw was old and broken
Removed the gas from the chain saw fuel tank
Removed chainsaw top cover
UN-bolted the carb air cleaner
Removed the carb
Pulled the old gas line out of the fuel tank
Pulled the new fuel line into the gas tank with forceps
Added a new fuel filter to the gas line in the fuel tank
Cut the new fuel line to length and inserted it into the fuel primer bulb
Reassembled the carb and air filter
Reinstalled the chainsaw top
Added fuel and started the chainsaw
The hard part is inserting the new fuel line into the fuel tank. I put a little oil on the fuel line and cut the line at an angle to start it. I used some forceps to pull the fuel line all the way down into the fuel tank.

Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Trimmer
Parts Used:
Fuel Line (25-Inch) - 530069247
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Pliers, T25 Torx driver, sharp knife or scissors,needle nose pliers.
Fuel line cracked and broken
This repair was a Craftsman hedge trimmer. Drain gas, remove fuel filter from inside tank, remove screws from trigger housing and remove trigger pull, remove two screws from handle facing which exposes entry port, gently pull fuel line from tank , disconnect from carburetor and discard. Connect new line to carb. route through hose clip, using scissors or sharp knife clip other end at angle with sharp point to one side so as to ease insertion into port on tank. Once inserted just a bit take long needle nose pliers and gently pull hose through and out the fill hole. Now with fuel line correctly placed in hose clip from carb to tank and remaining length pulled through tank, measure and cut the fuel line to about an inch outside the tank, push hose onto fuel filter and drop inside tank.
Reassemble remaining parts in reverse order fill with fresh fuel and replace cap and you're all set.
The screws in question are T25 Torx bit.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Product Information
Manufacturer: Craftsman
Product Number: 530069247
Classification: Part
Weight: 0.01 lbs.
Shipping: Ships Worldwide
Related Products
eReplacementParts.com
7036 South High Tech Dr.
Midvale, UT 84047
visa mastercard discover american express PayPal