Filter-air 13031000760
Part Number: 13031000760
Order within the next 6 hours
and your part ships today!
and your part ships today!
Product Information
Description:
This air filter replacement part is a high quality item that is specially designed for Echo backpack blowers. Its purpose is to filter out dust and debris from contaminating the engine. To replace this filter no special tools would be needed, simply remove the cover and replace the air filter. |
Frequently Purchased With
Compatibility
the 13 compatible machines
This part is compatible with the following machines:
Echo
PB-400 (001001-054522) Backpack Blower
PB-400 (054523) Backpack Blower
PB-400E (001001-128095) Backpack Blower
PB-400E (128096-249241) Backpack Blower
PB-400E -249242 Backpack Blower
PB-400E (Type 1E)(001001) Backpack Blower
PB-400 (054523) Backpack Blower
PB-400E (001001-128095) Backpack Blower
PB-400E (128096-249241) Backpack Blower
PB-400E -249242 Backpack Blower
PB-400E (Type 1E)(001001) Backpack Blower
PBAM-400E Mister Attachment
SV-2A Engine Lawn Equipment
SV-2AE Engine Lawn Equipment
PB-400 (054523-999999) Backpack Blower Lawn Equipment
PB-400E (249242-999999) Backpack Blower Lawn Equipment
SV-2A Engine Lawn Equipment
SV-2AE Engine Lawn Equipment
PB-400 (054523-999999) Backpack Blower Lawn Equipment
PB-400E (249242-999999) Backpack Blower Lawn Equipment
Little Wonder
Products Compatibility
This item works with the following types of products:
- • Blower
Questions & Answers for Filter-air
No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
1 of 1 people found this instruction helpful
Tool Type:
Trimmer
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Socket set
The Mantis tiller wouldn't start
I bought the K-10 carb rebuild kit and replaced the diaphragms in the carburetor. Mixed a fresh batch of 2 cycle gas and after a few pulls it started. The old air filter crumbled when I pulled it out so I replaced that too. The old one was the original from back in the late 80's. I also replaced the gasket in the fuel tank cap. The old seal was melted by the gas stored in the tank for a few years without being used. Over all a very easy repair that cost around $20. The last carb repair on this tiller was at least 8-10 years ago. At that time I replaced the diaphragms too.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Blower
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Absent air filters and flex tube dry rotted
Replaced air filters and simply secured flex tube with clamps. Very straight forward.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Blower
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers
Rotted fuel line /grommet in fuel tank.
This is a 38 year old Mantis mini tiller that was leaking fuel due to a rotted fuel tank grommet/fuel line. 1. Disconnected fuel line and removed tank.
2. Removed old fuel grommet/fuel line and fuel filter.
3. New Fuel line/grommet installed through side of tank and fuel filter on end of fuel line.
4. Connected fuel line to carburetor.
2. Removed old fuel grommet/fuel line and fuel filter.
3. New Fuel line/grommet installed through side of tank and fuel filter on end of fuel line.
4. Connected fuel line to carburetor.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Cultivator
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Wrench Set, Nutdriver
Lacked power
R and R cylinder , install rings, new gasket, rebuild carb
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Cultivator
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Adjustable Wrench
Air filter and on/off switch needed replacing. Parts and procedure very simple. Fuel line grommet needed in order to stop dribble from fuel tank.
Replacement of air filter and switch are obvious. Take off the old, replace with the new. (Don't try to solder the wire to the switch tag because it will melt the switch internal parts. Use a connector or crimp the bare wire to the tag and seal with tape or shrink wrap.) Fuel line grommet was a bit complicated because Mantis has changed fuel line and grommet diameter design over the years. The diameter of hole in tank and diameter of grommet might require some adjustments, depending on year of your equipment. The grommet I received did fit the tank perfectly, but the fuel line was just a bit tight fitting through the grommet. I had to work it fairly vigorously to get it through, but it did fit and works great. Tight to tank, and tight to fuel line. No leaks now.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Cultivator
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Solvent, paper towel
30 year fuel tank cleaning
I disconnected the fuel hose from the carbureter, removed the fuel tank brackets, discarded all of the original rubber parts, cleaned the tank thoroghly with solvent and paper towels, threaded the new fuel line into the tank, installed the new fuel filter, installed the check valve & gasket in the fuel cap. Re-installed the tank & mounting brackets, connected the fuel hose to the carburetor. Looks and works like new!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
3 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
3
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
Air Filter
This was a difficult part to find. Could'nt find it ANYWHERE eles. How does ereplacement have this ? It's beyond me. Perfect part. Thanks, Steve S.
Guest -
September 2, 2019
Verified Purchase
Exact part replacement
Perfect match...took less than 5 minutes to replace....
Guest -
July 4, 2019
Verified Purchase
Replacement Mantis Air Filter
Received OK - not used yet
Guest -
June 11, 2019
Verified Purchase
Verified Purchase
eReplacementParts Team
< PREV
- 1
Product Information