Curved Washer

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

, No tools needed.

The handle knob and curved washer came off while snow blowing and was lost in the snow somewhere and couldn't be found,even in the spring after the snow melted.

Extremely easy just installed the curved washer and the replacement knob, all by hand, no tools needed. It was a snap!!! Thanks for your prompt service!! Will definitely use you business again when necessary!!

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Missing parts

Reassemble push handle. Replaced missing pieces. Done.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Mower

Parts Used:

Retainer-Push On - 3290-320

Knob Handle - 106-4161

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

, Hammer

Handle bolts needed replacement

No tools needed for handle bolts since it is design for hand only removal.

Tire retaining push on required an hammer to hammer in the the part.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Knob Handle - 106-4161

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

, none

the original parts vibrated off

I put the bolt through the handle, put the washer on, and tightened the screw as tight as I manually could. They did not loosen on next use. So I call this repair a success

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Lock-Handle - 98-2266

Scraper - 55-8760

Repair Difficulty:

Medium

Time Spent Repairing:

1-2 hours

Tools Used:

Screwdriver, Pliers, Socket set, Wrench Set

Original scraper was worn and partially missing. One lock handle was bent and missing the curved washer.

Replaced bent lock handle with new part.

Removed old scraper by removing the three screws and nuts with socket set and wrench.
Used pliers to straighten the snow blower frame, making small adjustments and fitting the new scraper until it was straight.
Mounted the new scraper using the original screws and nuts. The screws had to be slowly tightened working right to left to pull the scraper into place.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

, None

Snow blower bolt and washer vibrated off from one side of handle

Put them on.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Knob Handle - 106-4161

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

, hand

knob vibrated loose and disappeared

bolt in hole knob on other end

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

, No tools needed

Lock handle and knob were missing on snowblower

Simply replaced lock handle, knob and washer. Nothing difficult.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Adjustable Wrench

I lost some parts which became loose and fell off while using it.

I got the parts from you and installed them

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used: