Easy
15-30 minutes
This replacement power cord is a genuine OEM sourced item that is specially produced for Black and Decker power tools. Its purpose is to supply electricity to the tool from a standard U.S. outlet. This high-quality rubber insulated cord is sold individually, please note the cord protector is included.
Cord/8 Foot /18-2sjt 330073-96
OEM part for: DeWALT, Black and Decker
Part Number: 330073-96
$31.49
In Stock
Order within the next 10 minutes and your part ships today! 
Compatibility
This part will fit the following 73 machines
Black and Decker
7448 Type 5 Sander View Diagrams & Manuals
7447 Type 1 Sander View Diagrams & Manuals
TV780 Type 1 Sander View Diagrams & Manuals
7308 Type 1 7 1/4 Circular Saw View Diagrams & Manuals
7308 Type 2 7 1/4 Circular Saw View Diagrams & Manuals
7308 Type 3 7 1/4 Circular Saw View Diagrams & Manuals
7308 Type 4 7 1/4 Circular Saw View Diagrams & Manuals
7308 Type 5 7 1/4 Circular Saw View Diagrams & Manuals
7308 Type 6 7 1/4 Circular Saw View Diagrams & Manuals
7308 Type 7 7 1/4 Circular Saw View Diagrams & Manuals
7308 Type 8 7 1/4 Circular Saw View Diagrams & Manuals
7358-04 Type 1 7 1/4 Circular Saw View Diagrams & Manuals
7358 Type 1 2 Horse Power Circular Saw View Diagrams & Manuals
7391 Type 1 Circular Saw View Diagrams & Manuals
7391 Type 2 Circular Saw View Diagrams & Manuals
7391 Type 3 Circular Saw View Diagrams & Manuals
7391 Type 4 Circular Saw View Diagrams & Manuals
7392 Type 1 2 Horse Power Circular Saw View Diagrams & Manuals
7392 Type 2 2 Horse Power Circular Saw View Diagrams & Manuals
7392 Type 3 2 Horse Power Circular Saw View Diagrams & Manuals
7392 Type 4 2 Horse Power Circular Saw View Diagrams & Manuals
7392 Type 5 2 Horse Power Circular Saw View Diagrams & Manuals
C2020 Type 1 6-1/2 Circular Saw View Diagrams & Manuals
TV510 Type 1 6-1/2 Circular Saw View Diagrams & Manuals
G-TS300 Type 2 3/8 Drill Keyless View Diagrams & Manuals
7190-04 Type 7 3/8 Variable Speed Reversible Drill View Diagrams & Manuals
7190 Type 2 3/8 Inch Value-Plus Variable Speed Reversible Drill View Diagrams & Manuals
7191A Type 1 7191 75th Anniversary Drill View Diagrams & Manuals
7191 Type 2 3/8 Drill View Diagrams & Manuals
7191 Type 3 3/8 Drill View Diagrams & Manuals
7224 Type 3 3/8 Horse Power 1/2 Drill View Diagrams & Manuals
7254-91 Type 1 1/2 Drill View Diagrams & Manuals
7254KC Type 2 1/2 Keyless Chuck Drill View Diagrams & Manuals
7254 Type 4 D3000 1/2 Reversible Drill View Diagrams & Manuals
7277-04 Type 2 Hammer Drill View Diagrams & Manuals
7277 Type 3 D4000 13MM Electric Speed Hammer View Diagrams & Manuals
HD2000 Type 2 1/2 Keyless Drill View Diagrams & Manuals
TS310 Type 1 3/8 Variable Speed Reversible Drill View Diagrams & Manuals
TS320 Type 1 1/2 Drill Variable Speed Reversible View Diagrams & Manuals
TS320 Type 2 1/2 Drill Variable Speed Reversible View Diagrams & Manuals
TV310 Type 1 T.V. 3/8 Variable Speed Reversible Keyless Drill View Diagrams & Manuals
TV380 Type 1 1/2 Variable Speed Reversible Keyless Drill View Diagrams & Manuals
23016 Type 1 Jig Saw View Diagrams & Manuals
9533 Type 2 9 Random Orbit Polisher View Diagrams & Manuals
9533 Type 1 9 Random Orbit Polisher View Diagrams & Manuals
9531 Type 2 7 Sander / Polisher View Diagrams & Manuals
9531 Type 1 7 Sander / Polisher View Diagrams & Manuals
9531S Type 2 7 Right Angle Sander View Diagrams & Manuals
9531-04 Type 2 7 Sander / Polisher View Diagrams & Manuals
9531-04 Type 1 7 Sander / Polisher View Diagrams & Manuals
7447-04 Type 1 Belt Sander View Diagrams & Manuals
7390 Type 8 Circular Saw View Diagrams & Manuals
7390 Type 7 Circular Saw View Diagrams & Manuals
7390 Type 6 Circular Saw View Diagrams & Manuals
24631 Type 2 Sander / Polisher View Diagrams & Manuals
TV600 Type 1 T.V. 1 HP Router View Diagrams & Manuals
7615 Type 3 1 1/2 HP Plunge Router View Diagrams & Manuals
7613 Type 4 1-1/2 HP Router View Diagrams & Manuals
7612 Type 2 Router View Diagrams & Manuals
7604 Type 4 1 HP Router View Diagrams & Manuals
7190-99 (Type 2) Double Insulated Drill View Diagrams & Manuals
7190V (Type 2) 3/8 Vsr Drill W/ Bits View Diagrams & Manuals
7191KBW (Type 3) 7191 W/30 Bit&kit View Diagrams & Manuals
C2020K (Type 1) Circular Saw Kit View Diagrams & Manuals
C2020KS (Type 1) 6-1/2 Circ Saw (Sams) View Diagrams & Manuals
7191KB (Type 3) 7191 W/12 Bits&kit View Diagrams & Manuals
7448-BDK (Type 5) 1/3 Sheet Finishing Sande View Diagrams & Manuals
7191KZ (Type 3) 3/8 Vsr Drill Kyls View Diagrams & Manuals
B7254 (Type 4) 1/2 Vsr Drill Power Tool View Diagrams & Manuals
B7358 (Type 1) 2 H.P. Circular Saw Power Tool View Diagrams & Manuals
DeWALT
B7254 (Type 4) 1/2-In. Vsr Drill View Diagrams & Manuals
B7358 (Type 1) 2 H.P. Circular Saw View Diagrams & Manuals
DW352-B3 (Type 1) 7-1/4 Circular Saw-Lac Power Tool View Diagrams & Manuals
Show More Compatible Models
This item works with the following types of products:
- Sander Parts
- Circular Saw Parts
- Saw Parts
- Drill Parts
- Hammer Drill Parts
- Jig saw Parts
- Polisher Parts
- Router Parts
This part replaces obsolete part #: 330073-42, 330073-94
Customer Part Reviews ?
Average Rating (out of 5):
Click to filter by ratings:
5 stars
4
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
ordreing the part was easy
the part came just as you said.thank you for all your help.
Guest -
May 6, 2020
Verified Purchase
EreplacementParts comes through again ...
I have ordered from you people many times and as always, you came through with flying colors! The part arrived almost too quickly! The quality is what I have come to expect when I order from your company. Thank you ...
Timothy -
January 1, 2020
Verified Purchase
Replacement Cord
Exact replacement with excellent online help.
Guest -
April 29, 2019
Verified Purchase
Great product and service.
The item I order was on time and exactly what I needed for my repair. I will use this service again.
Guest -
April 23, 2019
Verified Purchase
t
t
t -
t days ago
Verified Purchase
eReplacementParts Team
t
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Cord/8 Foot /18-2sjt
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
I cut the old power cord!
Clarence - May 20, 2016
👍 4 of 4 people found this instruction helpful
Tool Type
Circular Saw
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Wire cutter
Parts Used
I open the handle assembly, then removed the cord wires from the switch. I then connected the new cord wires to the switch and put the handles back together.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Old cord needed replacement
Gary - November 15, 2015
👍 2 of 2 people found this instruction helpful
Tool Type
Circular Saw
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Pliers
Parts Used
Removed 1 handle half of saw. Took an awl and pressed it in the switch where the cord wires are connected and pulled them out. Removed old cord, cut cord leads to correct length to connect to switch. Stripped the cord wires about 3/4 inch, twisted them. Then I put some solder on them to stiffen them up, then pressed them into the switch. Attached the handle. Pulled on the switch and it worked!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Power Cord was damaged.
Jerald - September 18, 2023
Tool Type
Circular Saw
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver, Heat Gun, Wire Stripper
Parts Used
Remove the screws that hold the two halves of the circular saw housing together. Then cut the bad cord as close as possible to the cord protective shielding to retain as much length of the original cord as possible. Then cut the replacement cord to have plenty excess length to route inside the circular saw housing so that the splicing ends (and 1/8" diameter heat shrink tubbing to cover the splice) will fit inside the housing void spaces without pinching any of the cord wires when the housing is screwed together. -- (Note: dry fit circular saw housing together without actually replacing the screws and adjusting the length of the wires if necessary.) Then cut a length of shrink tubing and slip it over the cut end of either the original, or replacement cord, making sure to allow about 1/4" exact on both ends of the shrink tubing to make sure it will completely cover the spice. Then use a wire stripper to strip about 3/4" of the coating from the ends of both cords, twist the stripped ends together, slide the shrink tubing in-place over the spice, and use a heat gun to shrink the tubing around the spice. Route the excess wires into the void spaces and carefully fasten the two halves of the circular saw housing together, making sure no wires get pinched and that the finger trigger for operating the saw moves freely.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
replaced power cord
DONALD - June 27, 2021
Tool Type
Circular Saw
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver
Parts Used
removed bad power cord had to cut and splice new cord to switch.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Cord was frayed
Daren - September 28, 2020
Tool Type
Circular Saw
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver, Wire strippers, awl, soldering iron and solder
Parts Used
1. Removed screws from handle
2. Used awl on switch to release old wires from switch
3. Used wire strippers to trim to correct length
4. Soldered the ends of the wires to firm up wires to place in switch
5. Replace screws back in handle
2. Used awl on switch to release old wires from switch
3. Used wire strippers to trim to correct length
4. Soldered the ends of the wires to firm up wires to place in switch
5. Replace screws back in handle
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Worn cord seemed damagerous
Ron - March 23, 2020
Tool Type
Circular Saw
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Pliers, wiring connections
Parts Used
Simply removed covers to expose wiring connection. Followed wiring color-code. Cut to fit. Attached connections. Replaced coverings. Checked function. Worked perfectly...and had two extra feet with new electrical cord replacement. Good, strong quality! Thanks. By the way, I've run the electrical hand saw now for 28-years...and counting....
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
