eReplacementParts.com
877-346-4814
Echo Parts
Repair Parts Home  Vacuum Parts  Echo Parts  A411000502 Coil, Ignition

Install
Videos!
Grid squares measure 1x1 inch
Coil, Ignition - A411000502:EchoCoil, Ignition - A411000502:EchoCoil, Ignition - A411000502:Echo

Coil,​​ Ignition A411000502

Part Number: A411000502
Echo
Availability: In Stock
Price: $76.93
Ships within 1 business day

*This part replaces obsolete part #: A411000501 and A411000500.

Product Information
Description:
This is a genuine OEM sourced replacement part, it is specially designed for use with Echo handheld lawn and garden equipment. The ignition coil also known as an armature-magneto provides the current for the ignition system by producing pulses of high voltage for the spark plugs. It is made of high-quality metal with a durable rubber insulated wire and is sold individually, keep in mind the spark plug boot is sold separately.
Frequently Purchased With
Compatibility

This part is compatible with the following machines:

Expand the 26 compatible machines
Products Compatibility

This item works with the following types of products:

  • • Blower
  • • Vacuum

Questions & Answers for Coil,​ Ignition


What are the readings for a bad ignition coil and a good ignition coil. My blower starts and runs fine but shuts off after 5 minutes and I can't start it back up until it cools down
Tyler for model number PB-250LN asked on 2022-11-17
Hello Tyler, Thank you for writing. That symptom sounds more like a dirty and out of tune carburetor, not a bad ignition coil. If you are not getting a spark then I recommend replacing the coil. The spark plug wire itself should read 2.5k to 5k OHMS, as for the other wires I have no specs for that but again this sounds more of a carburetor issue and I recommend spraying the inside of the carburetor with carburetor cleaner, you may want to tilt the engine so it runs out or with the engine running just spray a little at a time to prevent stalling the engine. If the problem persists then rebuild the carburetor as it may have some build-up of fuel breaking down in there. This happens over time. To tune a carburetor these are directions right from B&S. 1. Loosen the large set screw on top of the air filter with a flathead screwdriver and remove the air filter from the carburetor. 2. Locate the idle adjustment screw on the side of the carburetor. Gently turn the screw clockwise with a screwdriver until the valve touches the seat. Then, back the screw off counterclockwise for one-and-a-half turns. 3. Look on the opposite side of the carburetor, for the high-speed adjustment screw -- if your carburetor has one. Gently turn the screw clockwise until the valve touches the seat, then back this screw off one-and-a-half turns as well. 4. Check to see if your engine has a large bowl on the bottom side of the carburetor that houses the float. If so, it will have a single screw on the bottom of the bowl. Turn the screw clockwise until it stops turning, then back it off for one-and-a-half turns. 5. Replace the air filter on top of the carburetor and secure it by tightening the screw in the centre of the air filter. 6. Start the engine and let it half-throttle for about five minutes to warm up. Then, slowly turn the idle adjustment screw -- which you adjusted in Step 3 -- clockwise until the engine begins to slow. Note the position of the screw and then begin turning the screw counterclockwise. The engine will normalize, then eventually will begin to slow once again. Note the position where it begins to slow a second time and rotate the screw clockwise to a point halfway between the two positions where the engine began to slow. You have now fine-tuned the idle adjustment. 7. Increase the throttle to full speed. Repeat the adjustments you made on the idle screw on the high-speed screw -- on the opposite side of the carburetor from the idle screw. 8. Test the engine under varying workloads. If the engine runs roughly under any conditions, adjust the idle or high-speed screw to fine-tune the adjustments. I hope this helps and good luck with your repair.
eReplacementParts Team November 17, 2022
Repair Instructions: Submitted by Customers Like You
Tool Type:
Blower
Parts Used:
Coil, Ignition - A411000502
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Power Drill, Socket set
Would not start. Coil had to be replaced.
Watched video online about how to replace coil.
Was very informative and full of suggestions on how to make task easier.
Followed their instructions and made it possible for an amateur to accomplish the repair.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Blower
Parts Used:
Spark Plug Coil - 15901103432
Spark Plug Cap - 15901203433
Coil, Ignition - A411000502
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Socket set, Wrench Set, Nutdriver, Allen wrench
Ignition broke
Go to utube and put the unit model.in there and the explanation of ignition is in there. It's really easy to follow.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Blower
Parts Used:
Wing Bolt - 21041752730
Air Filter Cover - 13031305863
Coil, Ignition - A411000502
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers, Socket set, feeler gauge
coil failed
removed coil and installed new one
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Blower
Parts Used:
Coil, Ignition - A411000502
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Socket set, Solder gun
Magneto was bad
Disassembled, installed, gaped contact point,
Soldered sparkplug end reassembled
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Blower
Parts Used:
Coil, Ignition - A411000502
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers, Torx screwdrivers
No fire.
You tube video on coil replacement my make and model.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 2 people found this instruction helpful
Tool Type:
Blower
Parts Used:
Coil, Ignition - A411000502
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
, Torx
No spark @ spark plug
This was on an Echo leaf blower.....removed all plastic covers, removed flywheel and then the ignition coil. Put new coil on and set gap with a business card and tightened screws back together and covers back on. Add new fuel, started second pull. Easy peasy.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Blower
Parts Used:
Coil, Ignition - A411000502
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers, Power Drill
Died would not start
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 2 people found this instruction helpful
Tool Type:
Blower
Parts Used:
Coil, Ignition - A411000502
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver
Coil replacement on leaf blower
Removed covers
Removed blower assembly removed engine mounts to case
Removed and replaced coil and set clearance at 0.014
Reassemble and started
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 2 people found this instruction helpful
Tool Type:
Blower
Parts Used:
Coil, Ignition - A411000502
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
, Torx driver
No start. No spark.
1. Troubleshoot and found no spark
2. Disassembled and troubleshoot to eliminate bad run/off switch as cause of problem
3. Disassembled and replaced coil assembly.
4. Used index card to set coil to flywheel/magnet air gap.
5. Reused boot, plug attachment hardware.
6. Assembled

Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 2 people found this instruction helpful
Tool Type:
Blower
Parts Used:
Coil, Ignition - A411000502
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Socket set
Ignition coil went out
1. Removed plastic housings/shroud.
2. Removed blower fan.
3. Removed the last shroud.
4. Removed broken ignition coil paying attention to orientation.
5. Removed spark plug boot from old ignition coil and installed on new ignition coil.
6. Installed new ignition coil using a business card to set the gap between ignition coil and magnets on flywheel.
7. Installed shroud, blower fan and housings in reverse order.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
4.8
Average Rating (out of 5):
6 Reviews
Click to filter by ratings:
5 stars
5
4 stars
1
3 stars
0
2 stars
0
1 stars
0
  • Highest Rating
  • Most Recent
< PREV
  • 1
NEXT >
  • worked as expected
    coil arrived on time in great condition. blower working again.
    Guest - May 30, 2022 Verified Purchase
    Exactly what was needed.
    Part fit and worked perfectly.
    John - March 26, 2021 Verified Purchase
    Repair
    This was easy to do and when I finished second pull and started right up. Bob
    Guest - November 7, 2020 Verified Purchase
    Coil Ignition
    Ordered, delivered, helpful and timely!
    SCOTT - September 23, 2019 Verified Purchase
    Part was exactly same as original. Fit perfectly.
    Was in excellent condition. Arrived on time. Every part I have ordered from ereplacementparts.com exceeded my expectation.
    Ernie - April 26, 2019 Verified Purchase
    easy site to work with
    web site was easy to navigate parts were just what i needed. price was market. was shipped in a short time. was very pleased. all is working well.
    Guest - April 21, 2020 Verified Purchase
    Verified Purchase
    eReplacementParts Team
    • Highest Rating
    • Most Recent
    < PREV
    • 1
    NEXT >
    Product Information
    eReplacementParts.com
    7174 South 400 West
    Suite 5
    Midvale, UT 84047
    visa mastercard discover american express PayPal