Carburetor-wyj-250a A021000053
Part Number: A021000053
Order within the next 2 hours
and your part ships today!
and your part ships today!
*This part replaces obsolete part #: A021000052.
Product Information
Description:
This is an original replacement part manufactured for use with Echo outdoor power equipment. Gaskets, valves, fuel passages can wear out or constrict over time causing the carburetor to decline or stop working. Some symptoms of a declining carburetor are trouble starting, not starting, irregular idle, excessive fuel consumption, or fuel leakage. Replacing a bad carburetor can extend the performance life of the engine. This carburetor is complete and sold individually, it is recommended to replace the gasket when servicing the carburetor to assure a good seal, please see model diagram for additional parts. |
Frequently Purchased With
Compatibility
the 17 compatible machines
This part is compatible with the following machines:
Echo
SRM-260 (03001001 - 03999999) Straight Shaft Trimmer / Brushcutter
SRM-260 (04001001 - 04999999) Straight Shaft Trimmer / Brushcutter
SRM-260S (03001001 - 03999999) Straight Shaft Trimmer / Brushcutter
SRM-260S (04001001 - 04999999) Straight Shaft Trimmer / Brushcutter
SRM-261SB (02001001 - 02999999) Straight Shaft Trimmer / Brushcutter
SRM-261S (02001001 - 02999999) Straight Shaft Trimmer / Brushcutter
SRM-261 (02001001 - 02999999) Straight Shaft Trimmer / Brushcutter
PPT-260 (03001001-03006148) Power Pruner Telescoping Shaft
PPT-260 (03006149-03999999) Power Pruner Telescoping Shaft
SRM-260 (04001001 - 04999999) Straight Shaft Trimmer / Brushcutter
SRM-260S (03001001 - 03999999) Straight Shaft Trimmer / Brushcutter
SRM-260S (04001001 - 04999999) Straight Shaft Trimmer / Brushcutter
SRM-261SB (02001001 - 02999999) Straight Shaft Trimmer / Brushcutter
SRM-261S (02001001 - 02999999) Straight Shaft Trimmer / Brushcutter
SRM-261 (02001001 - 02999999) Straight Shaft Trimmer / Brushcutter
PPT-260 (03001001-03006148) Power Pruner Telescoping Shaft
PPT-260 (03006149-03999999) Power Pruner Telescoping Shaft
PPT-260 (04001001-04001102) Power Pruner Telescoping Shaft
PPT-260 (04001103-04999999) Power Pruner Telescoping Shaft
PPT-261 (02001001-02004193) Power Pruner Telescoping Shaft
PPT-261 (02004194-02999999) Power Pruner Telescoping Shaft
PPT-261 (06001001-06999999) Power Pruner Telescoping Shaft
PAS-260 (03001001 - 03999999) 24.5 cc Pro Attachment
PAS-260 (04001001 - 04999999) 24.5 cc Pro Attachment
PAS-261 (02001001-02999999) Power Head Straight Shaft Edger Attachment
PPT-260 (04001103-04999999) Power Pruner Telescoping Shaft
PPT-261 (02001001-02004193) Power Pruner Telescoping Shaft
PPT-261 (02004194-02999999) Power Pruner Telescoping Shaft
PPT-261 (06001001-06999999) Power Pruner Telescoping Shaft
PAS-260 (03001001 - 03999999) 24.5 cc Pro Attachment
PAS-260 (04001001 - 04999999) 24.5 cc Pro Attachment
PAS-261 (02001001-02999999) Power Head Straight Shaft Edger Attachment
Products Compatibility
This item works with the following types of products:
- • Pruner
- • Trimmer
Repair Guides
Articles:
Filthy Filters? This article will show you how to install a filter kit on an Echo SRM-225 trimmer....
May 27, 2015
|
Questions & Answers for Carburetor-wyj-250a
No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
3 of 3 people found this instruction helpful
Tool Type:
Pruner
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Old carburator was flooding out
Remove air filter cover to expose the 2 mounting screws. Then detach the two fuel lines from carb and take off of the engine. Loosen the lock nuts holding the so you can remove the carb linkage cable. Insert linkage cable into butterfly on top of new carb and tighten the 2 lock nut. Then place gasket on carb, feed the screws through the mounting flange for the air filter, and tighten the 2 screws to insure good seal.
Push the primer bulb 5 or 6 times and then pull starter cord. If motor doesn't start, prime the carb again. Check to be sure the ignition switch is set to on position and pull starter cord.
Push the primer bulb 5 or 6 times and then pull starter cord. If motor doesn't start, prime the carb again. Check to be sure the ignition switch is set to on position and pull starter cord.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
2 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
2
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
OEM Carburetor for Echo 260
My 23 year old echo carb. started acting up. Rather than rebuilding it I chose to buy new. This carb works flawlessly. I bolted it up and with no adjustments my 23 yr. old weed eater runs as it did when it was brand new.
Guest -
June 5, 2023
Verified Purchase
Ok
A good price works good to
HOMER -
May 23, 2019
Verified Purchase
Verified Purchase
eReplacementParts Team
< PREV
- 1
Product Information
Repair Guides
Articles:
Filthy Filters? This article will show you how to install a filter kit on an Echo SRM-225 trimmer....
May 27, 2015
|