Carburetor A021003661

Description:

This genuine OEM supplied carburetor is designed for Echo handheld blowers/vacuums. Its primary function is to mix air and gas before the fuel mix goes to the engine. This is a metal body carburetor with a rubber primer bulb. Please note gaskets are sold separately.

If the engine starts and then quickly dies, replacing carburetor may resolve this issue.

You would need a torx screwdriver to complete this repair.

• Remove the air cleaner cover, filter and the base
• Remove old carburetor and install new one
• Re-assemble and test the equipment

Frequently Purchased With

Air Filter
$7.09

Fuel Filter
$5.36

Gasket-intake..
$5.19

Tune-up Kit
$19.91

Spark Plug
$3.99

Carburetor Rep..
$16.48

Compatibility

This part is compatible with the following machines:

Echo

ES-250 (P33612001001-P33612999999) 25.4 cc Shred 'N' Vac
ES-250 (P33711001001-P33711999999) 25.4 cc Shred 'N' Vac
ES-250 (P33813001001-P33813999999) 25.4 cc Shred 'N' Vac
PB-250 (P33112001001-P33112999999) Handheld Blower
PB-250 (P33211001001-P33211999999) Handheld Blower
PB-250LN (P34913001001-P34913999999) 25.4 cc Handheld Blower
PB-250LN (P34712001001-P34712999999) 25.4 cc Handheld Blower
PB-250LN (P34811001001-P34811999999) 25.4 cc Handheld Blower
PB-250LN (P38211001001 - P38211999999) Handheld Blower

PB-250LN (P40212001001 - P40212999999) Handheld Blower
PB-250LN (P40313001001 - P40313999999) Handheld Blower
ES-250 (P38311001001 - P38311999999) Shred 'N' Vac
ES-250 (P40412001001 - P40412999999) Shred 'N' Vac
ES-250 (P40513001001 - P40513999999) Shred 'N' Vac
ES-250 (P41814001001-P41814999999) Chipper Shredder Lawn Equipment
PB-250LN (P39926001001-P39926999999) Handheld Blower Lawn Equipment
PB-250LN (P42814001001-P42814999999) Handheld Blower Lawn Equipment

Expand the 17 compatible machines

Products Compatibility

This item works with the following types of products:

• Blower
• Vacuum

Repair Instructions: Submitted by Customers Like You

3 of 3 people found this instruction helpful

Tool Type:

Blower

Parts Used:

Carburetor - A021003661

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Socket set, Wrench Set

No power

I removed the air filter assembly, removed the fuel lines form the old carb. Then installed them in the same place on the new carb. Installed air filter assembly. Primed it a few times. The blower started on the 3rd pull, and ran like it was new.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

2 of 2 people found this instruction helpful

Tool Type:

Blower

Parts Used:

Carburetor - A021003661

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Screwdriver

My blower would not run except when it was fully choked. However, even on full choke it would only run about 50% rpm's.

To replace the carburetor it was one of the easiest repairs I have ever done. It took me about 10 minutes and my blower is running as good as new.
All I did was remove the air filter. Then two screws, removed the fuel lines, then the old carburetor. Put the new carburetor on with the screws, replaced the fuel lines. And replaced the air filter

Did you find this story helpful?

Thanks for voting and helping fellow customers!

1 of 1 people found this instruction helpful

Tool Type:

Blower

Parts Used:

Carburetor - A021003661

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver

Not getting fuel

Remove the air filter cover and air filter. Remove the fuel lines from the carburetor. Remove the to screws holding the old carburetor. Remove the old carburetor and install the new one. Replace the two screws and tighten them. Attach the fuel lines to the new carburetor. Attach the air filter assembly.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

1 of 1 people found this instruction helpful

Tool Type:

Blower

Parts Used:

Carburetor - A021003661

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver

Would not run without choke being halfway closed. Would not reach high RPM.

There was obviously a partially clogged passage in he carburetor that I couldn't get cleared. Replacement carburetor was a simple operation. Two screws and the fuel lines. Done and it now runs fine.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Blower

Parts Used:

Carburetor - A021003661

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Nutdriver, Needle nose pliers to remove fuel lines

Carburetor would not allow fuel to the engine. Cleaned and still no fuel flow.

Removed the old carburetor and installed the new carburetor by removing four torx head bolts and reinstalling same.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Blower

Parts Used:

Carburetor - A021003661

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Screwdriver, Star socket

Carburetor was bad

Remove the air filter cover and filter
Remove the fuel lines and throttle from the carburetor
Remove the screws holding the carburetor and air cleaner base
Remove the old carburetor
Install the carburetor and air cleaner base on the the two screws
Attach the fuel lines and throttle to the carburetor
Install the filter and filter cover

Did you find this story helpful?

Thanks for voting and helping fellow customers!

0 of 1 people found this instruction helpful

Tool Type:

Blower

Parts Used:

Carburetor - A021003661

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Nutdriver

Loss of power

Removed old carb and replaced with new.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Reviews

Average Rating (out of 5):

6 Reviews

Click to filter by ratings:

5 stars

4

4 stars

2

3 stars

0

2 stars

0

1 stars

0

Sort by:

Highest Rating
Most Recent

< PREV

1

NEXT >

New carburetor for Echo blower

Blower ran very rough and would never run at full throttle. In less than 15 minutes I installed a new carburetor (A021003661), and it started on the second pull and ran like a new unit. It was an easy repair with the right part.

Guest - September 1, 2023 Verified Purchase

quality part

hard to find locally, factory parts at unbeatable prices

James - February 25, 2021 Verified Purchase

Well worth the price

Had issues with echo blower which I tried adjusting carb but couldn’t set it properly. Had issues with starting and full throttle. New carb installed in 5 minutes. Starts right up on 2nd pull every time. No bogging issues at full throttle anymore. Great investment n quicker then trying to readjust old carb.

Guest - June 18, 2019 Verified Purchase

Right part;easy fit.

A little skeptical at first replacing a carburetor, but out with the old and in with the new in about half an hour. Saved myself a few bucks by doing it myself, made possible by Replacement Parts and their terrific website. Surprised by the flimsy Echo OEM carb that failed.

Guest - April 22, 2019 Verified Purchase

This was the widest thing I have seen. The little hand blower was working fine and died. Ok bad gas. changed the gas no good. spark good compression ok. Timing??? Who knows. Got a new carb and it was no good. Must be timing. pulled it down and the key was good put back and now i was getting 50 pound of compression. What happened. Did i swallow a valve. Shot some oil in and pulled it through and with the new carb on it and it fired. You tell me what was wrong. Wally

They are so responsive to the order i left the parts on the bench while the new carb was coming to me.

Guest - August 28, 2021 Verified Purchase

Right part. Easy to install.

Guest - April 26, 2021 Verified Purchase

Verified Purchase

eReplacementParts Team

Sort by:

Highest Rating
Most Recent

< PREV

1

NEXT >

Questions & Answers for Carburetor