Carburetor Gasket 16228-ZL8-000

Carburetor - 16100-Z0L-023

Air Cleaner Case Assembly - 17220-ZM0-030

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Socket set

Engine surging due to carburetor problem

1. Removed the air filter
2. Unbolt the carburetor and air cleaner case
3. Removed control linkage
4. Remove carburetor, clean off all gasket residue
5. Install new gasket and carburetor, all of the pieces must be staged on the two carburetor bolts.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

3 of 3 people found this instruction helpful

Tool Type:

Lawn Mower

Parts Used:

Air Cleaner Gasket - 17228-ZM0-000

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Socket set

It was not running properly

I cleaned out the carburetor for spring and disassembled the carburetor. When I pulled out the two bolts that hold the air cleaner to the carburetor, the carburetor and all of the gaskets fell out. when I replaced them my mower did not run properly. I bought a workshop manual and all new gaskets to show me the orientation of the gaskets and it runs as good as the day I purchased it.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

1 of 1 people found this instruction helpful

Tool Type:

Lawn Mower

Parts Used:

Carburetor Assy - Bb62j B - 16100-Z0Y-813

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Socket set

Lawnmower was running poorly.

I followed the video you guys made. Very well done. Thanks

Did you find this story helpful?

Thanks for voting and helping fellow customers!

2 of 3 people found this instruction helpful

Tool Type:

Engine

Parts Used:

Carburetor Assembly - 16100-Z0L-862

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Pliers, Socket set

Engine only runs on starting fluid.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

1 of 2 people found this instruction helpful

Tool Type:

Engine

Parts Used:

Fuel Filter - 16952-ZA8-800

Carburetor Assembly - 16100-Z0J-013

Guide- Air - 19650-ZL8-000

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Pliers, Socket set, Wrench Set, Mat and magnet (small needlenose pliers for clips).

Honda GC160 carb too gummed up.

CHEAPER and FASTER to replace carburetor assembly and gaskets than to disassemble and clean/replace parts. Had already determined carb problem(s). Started 2nd pull after reassembly and after warmed up adjusted idle speed. Now my pressure washer is ready when I need it.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Mower

Parts Used:

Air Cleaner Case Assembly - 17220-ZM0-030

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Nutdriver

Air cleaner case had cracked at the snaps.

Pulled old case off. I studied the on line video which was very helpful. On the video he does the repair by himself. I strongly suggest a second pair of hands that can hold the assembly together as you slip on the gaskets, governor etc.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Mower

Parts Used:

Carburetor - 16100-Z0L-023

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Socket set

Carburetor and gaskets were bad.

Removed the carburetor and the old gaskets. Replaced with the new carburetor and the new gaskets.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Engine

Parts Used:

Carburetor Insulator - 16211-ZL8-000

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Socket set

The carburetor needed replaced.

1. Removed the 2 bolts holding the carburetor to the engine, using a socket set.
2. Removed the fuel line.
3. Removed the carburetor.
4. Put on the new carburetor.
5. Replaced the fuel line.
6. Reinserted the 2 bolts that fasten the carburetor to the engine.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Engine

Parts Used:

Bolt- Flange - 6x79 - Ct200 - 90004-ZL8-000

Gasket- Air Cleaner - 17228-ZL8-000

Tube- Breather - 15721-ZL8-000

Carburetor Assembly - 16100-Z0J-013

Spark Plug - 98079-56846

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Pliers, Socket set, Wrench Set

Replaced carb on tiller 5 HP Honda engine. Was back firing and low power.

Found a couple of videos to look at before doing the repair. Took my time. Removed fuel tank. Drained fuel tank. Removed air box and filter. Removed Carb. Linkage was a bit tricky but it turned out well. Hoses removed fairly easy. Also replaced fuel filter and air filter. All went back together well. Also put in new spark plug and changed oil. Fresh gas and ready to go. A few pulls to get started as the carb was dry. Runs great. Just be careful not to bend linkage or stretch springs.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Engine

Parts Used: