866-322-9842
Mon-Fri 7am-1am EST
Sat-Sun 7am-11pm EST
Repair Parts Home  Power Tool Parts  Bosch Parts  1607014176 Carbon Brush Set

Carbon Brush Set

Part Number: 1607014176
Bosch

We Sell Only Genuine Parts From the Manufacturer – Guaranteed!

Availability: 25+ in stock
Price: $12.68
Quantity:
Ships within 1 business day

*This part replaces obsolete part #: 1607014172 and 1607014138.

Description:
Genuine Bosch replacement part
Set of 2 Carbon Brushes with wire lead attached.

• Worn brushes frequently are the cause behind a motor running poorly.
• Replacing brushes can fix a motor that’s operating intermittently.
• New brushes can restore a motor’s electric braking.


Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Product Information
Manufacturer: Bosch
Product Number: 1607014176
Classification: Part
Weight: 0.01 lbs.
Also Known As: Motor Brush Set
Shipping: Ships Worldwide
Products Compatibility

This item works with the following types of products:

  • • Grinder
  • • Saw
Questions & Answers

No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
2 of 2 people found this instruction helpful
Tool Type:
Grinder
Parts Used:
Carbon Brush Set - 1607014176
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
the grinder wouldn't rotate
Removed the back housing and then it was out with the old and in with the new replace the housing done. Fran
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Grinder
Parts Used:
Spanner Wrench - 1607950052
Carbon Brush Set - 1607014176
Grommet - 1600703031
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers
Grinder would not turn on
I checked the power cord and on/off switch for continuity and both were good
I removed the motor contact brushes and noticed that they were significantly worn down
I also noticed a small spring protruding from one of the contact brushes
The common fix note on the website stated that one of the most common fix for my problem was brush replacement.
Ordered the replacement brush set and installed easily.
Grinder works great
Note: I used the exploded parts diagram to figure out how to disassemble the tool
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Grinder
Parts Used:
Carbon Brush Set - 1607014176
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Slotted Screwdriver, Continuity Tester
My Bosch 1810PS 4-1/2" Grinder stopped working. No Sound, No Movement whatsoever
1.) Unplugged unit.
2.) Using a Slotted Screwdriver or T15 Torx, I removed the (4) screws holding the two covers over power switch. I then pried the two covers apart and off the tool with a slotted screwdriver.
3.) Using a Digital Multimeter (a VOM or Continuity Tester will work also) I checked for continuity thru both wires in the power cord one at a time from the plug prongs to the power switch. I made sure to wiggle the power cord while checking continuity. I had continuity thru both wires.
4.) Next using the Multimeter I did the same continuity check for both poles of the power switch, one pole at a time. This also checked out OK.
5.) Next using a small Slotted Screwdriver I released the spring holding tension on one brush in its holder. I pulled the brush out while leaving its braided wire still connected to its terminal.
6.) The brush still appeared to have some life left in it by its size, but there was a black plastic pin sticking out of the brush face. Bosch has incorporated a spring loaded plastic tipped plunger into the back of the brush and this plunger is exposed when the brush wears down to a certain height. When the plunger is exposed the spring in the plunger lifts the brush off of the commutator so no electrical connection is made and the tool will not work. Bosch did this to save the tool from being destroyed by running the brushes down to the very end. So it appeared at this point all I needed was brushes. The commutator looked good.
7.) I also checked for continuity thru both stator coils with the multimeter. This required unplugging both brushes, one at a time. I used a small pair of needle nose pliers to unplug the brushes. The Stator Coils also checked fine.
8.) So I ordered a new pair of brushes. I installed them making sure the brush braided cable is routed correctly so as to not inhibit brush movement. I reinstalled both covers over the switch, powered up the tool, and it worked just fine.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Grinder
Parts Used:
Carbon Brush Set - 1607014176
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
My grinder stopped working suddenly, changing the brushes would be the most inexpensive first step.
I removed the housing on the grinder lifted up the tension springs that's one on each side pulled out the electrical connections lifted the old brushes out and replaced with the new ones. The grinder works fine. Before finding your web site we would buy new grinders. Thanks Again Fran F.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Grinder
Parts Used:
Carbon Brush Set - 1607014176
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers, Little pick or piece of wire to raise spring
Arcing at commutator
Carefully remove 1/2 of rear case at a time and replace plug in brush, to avoid having to readjust placement of trigger, springs etc. Easy on this one, had no other problems.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Grinder
Parts Used:
Carbon Brush Set - 1607014176
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Worn brushes
Remove back cover, pull spring end and place to the side if the brush holder. Remove old brushes from terminals. Install the new brushes in reverse order.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Discussion
Discussion for Carbon Brush Set - ( 1607014176 )
Discussion is closed. To ask our experts a question about a part, use the Q&A feature.
visa mastercard discover american express PayPal
HACKER SAFE certified sites prevent over 99.9% of hacker crime.

fancyboxy