*This part replaces obsolete part #: N408735, N039389 and 622437-00.
Product Information
| Manufacturer: DeWALT, Black and Decker |
| Product Number: N558583 |
| Classification: Part |
| Weight: 0.01 lbs. |
| Also Known As: Motor Brush |
| Shipping: Ships Worldwide |
Specifications
|
Description:
| This is a genuine Dewalt replacement part, it is sold individually. Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor’s electric braking
|
Compatibility
Products Compatibility
This item works with the following types of products:
- • Chop Saw
- • Saw
Questions & Answers
6124 angle polisher buy Black & Decker will these brushes fit
John
for model number Type 100 angle polisher 2300 RPM
asked on 2019-07-22
Hello John, thank you for your question. This Carbon Brush is not shown as compatible to your model. Unfortunately for your model the replacement is discontinued and is no longer available. We have no known replacement information in our system. We recommend you contact Black and Decker directly to see if they have recently released a new substitute. Please feel free to get back in touch with us to place an order if they provide a substitution part number. Thank you.
Repair Instructions: Submitted by Customers Like You
8 of 9 people found this instruction helpful
Tool Type:
Chop Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Torx screwdriver
Saw stop running
Removed the rear motor cover with a torx screwdriver 2 screws. Remove the brush retainer caps, remove the old brushes, install the new brushes, reinstall the brush retainer caps & rear motor cover.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
6 of 7 people found this instruction helpful
Tool Type:
Chop Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Saw wouldn't run smoothly, brushes worn
I removed the brush caps with a screwdriver, then I removed the worn brushes, and installed the new brushes. I then screwed the brush caps back in. Easy fix.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Chop Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Brushes burned up
Remove the brush caps, removed the old brushes, install the new brushes, replace the brush caps.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Chop Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, None
Brushes worn out on my DeWalt saw
Easy, use a screwdriver off take the end cap. Then remove the brush caps with a screwdriver. Then pull the worn brushes out, and install the new ones. Replace the brush caps and the end cap. And your done. I would recommend ereplacement parts to anyone.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 4 people found this instruction helpful
Tool Type:
Chop Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Tool sparked but wouldn't run, brushes worn
With a screwdriver remove the the brush caps, Then remove the worn brushes. Clean out the brush holders with compressed air and inspect the armature for any signs of damage. Then install the new brushes in the holder and screw the brush caps back on.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Chop Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
The carbon brushes wore out.
1. Removed the original carbon brushes.
2. Cleaned the motor with spray type electrical cleaner.
3. Places order for new brushes
4. Upon receipt, checked new parts for correctness and or damage
5. Installed new brushes
6. Performed test
7. Test Satisfactory.
2. Cleaned the motor with spray type electrical cleaner.
3. Places order for new brushes
4. Upon receipt, checked new parts for correctness and or damage
5. Installed new brushes
6. Performed test
7. Test Satisfactory.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Chop Saw
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers, Nutdriver, small flat file
Brush lead broken off brush body and warped the holder due to high heat generated.
1. Removed end cover (2 screws)
2. removed brush holder caps and remove old brushes.
3. Loosen set screw holding brush holder. Removed the warped brush holder with pliers & screwdriver. Case was slightly warped due to the excess heating so the holder came out in several pieces.
4. Clean rotor contacts with electrical contact cleaner to remove carbon buildup.
5. Used small file to smooth out case sides for new brush holder to fit back in. Inserted new holder and tighten set screw back down.
6. Install new pair of brushes and holder caps. Reinstall end cap.
7. Test ran chop saw to ensure a good repair.
2. removed brush holder caps and remove old brushes.
3. Loosen set screw holding brush holder. Removed the warped brush holder with pliers & screwdriver. Case was slightly warped due to the excess heating so the holder came out in several pieces.
4. Clean rotor contacts with electrical contact cleaner to remove carbon buildup.
5. Used small file to smooth out case sides for new brush holder to fit back in. Inserted new holder and tighten set screw back down.
6. Install new pair of brushes and holder caps. Reinstall end cap.
7. Test ran chop saw to ensure a good repair.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Chop Saw
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Replace brushes
Remove old brushes and install new brushes
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Chop Saw
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers, ....
broken connector & backed wire ends .
Have a problem with brush wire connector. The wire end was bunt and a new end was installed
which does not hold well , in use it comes off . Have go back into saw to fix . No part number for the right kind of connector .
which does not hold well , in use it comes off . Have go back into saw to fix . No part number for the right kind of connector .
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Chop Saw
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, Nutdriver, Torx bits
Brushes burnt, switch stuck
Removed/repaired switch which had burnt plastic lip keeping one set of contacts from engaging. One of brushes out of tolerance, would not engage armature due to being slightly over sized. Had to scrape/sand bush in areas due to excess thickness to fully seat in brush holder deep enough to engage armature...Just an unexpected problem which was easily corrected once enough light showed problem with brush not engaging.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
show more
Reviews
3 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
3
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
Easy Fix thanks for the sale and fast shipping
Work great, fast shipping and parts are good, easy fix for chop saw
Guest -
October 22, 2019
Verified Purchase
Just what I needed
The chop saw used on the job went to acting acting weak like it had lost a lot of power and smoking some. Ordered new carbon brushes for it and now the saw works like new again. Excellent prices and fast service. I always come shopping at ereplacement parts when I need help to get my tools up and running again. Thank you for the great service!
Guest -
July 27, 2019
Verified Purchase
Great parts
arrived very quickly. Thanks
Guest -
June 5, 2019
Verified Purchase
Verified Purchase
eReplacementParts Team
< PREV
- 1
Product Information
| Manufacturer: DeWALT, Black and Decker |
| Product Number: N558583 |
| Classification: Part |
| Weight: 0.01 lbs. |
| Also Known As: Motor Brush |
| Shipping: Ships Worldwide |
Repair Guides
Watch the Repair Video for
Carbon Brush
Articles:
|
Saw won't start? Step-by-step instructions show you how to quickly remove and install new motor brushes on your DeWALT c...
June 29, 2016
|
