eReplacementParts.com
877-346-4814
Fein Parts
Repair Parts Home
  
Power Tool Parts
  
Fein Parts
  30711129009 Carbon Brush

Carbon Brush 30711129009

OEM part for: Fein

Part Number: 30711129009


Install
Videos!
Carbon Brush - 30711129009:Fein 360 View
Carbon Brush - 30711129009:FeinCarbon Brush - 30711129009:FeinCarbon Brush - 30711129009:Fein 360 View
In Stock
Order within the next 11 hours and your part ships today!
Easy 15-30 minutes (13 rated repairs)?
OEM: Original Equipment Manufacturer ?
Fein
Does this d-block d-md-none fit my product?

Product Description ?

Genuine fein replacement part
This brush is sold individually, 2 are needed for the tools shown below
It is always best to replace both brushes, even if only one is worn.

Worn brushes frequently are the cause behind a motor running poorly.
Replacing brushes can fix a motor that’s operating intermittently.
New brushes can restore a motor’s electric braking.

Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

  • Wire end to end: 1.95
  • Classification: Part
  • Weight: 0.01 lbs.
  • Shipping: Ships Worldwide

Frequently Purchased Together ?

Compatibility

This part will fit the following 34 machines

Fein

MSX636II (72292609364) MultiMaster View Diagrams & Manuals
MSX636II (72292612368) MultiMaster View Diagrams & Manuals
MSX636II (72292613110) MultiMaster View Diagrams & Manuals
MSX636II (72292624117) MultiMaster View Diagrams & Manuals
MSX636II (72292624233) MultiMaster View Diagrams & Manuals
MSX636II (72292697360) MultiMaster View Diagrams & Manuals
MSX636II (72292698360) MultiMaster View Diagrams & Manuals
MSXE636II (72292709360) MultiMaster View Diagrams & Manuals
MSXE636II (72292712364) MultiMaster View Diagrams & Manuals
MSXE636II (72292713368) MultiMaster View Diagrams & Manuals
FMM250 (72293609360) MultiMaster View Diagrams & Manuals
FMM250 (72293612360) MultiMaster View Diagrams & Manuals
BSS2.0 (72302200116) Slitting Shears View Diagrams & Manuals
BSS2.0 (72302209365) Slitting Shears View Diagrams & Manuals
BSS2.0 (72302212369) Slitting Shears View Diagrams & Manuals
BSS1.6 (72302709362) Slitting Shears View Diagrams & Manuals
BSS1.6C (72302809368) Slitting Shears View Diagrams & Manuals
BLS2.5 (72302612360) Sheet Metal Shears View Diagrams & Manuals
BLS1.6X (72302912368) Sheet Metal Shears View Diagrams & Manuals
BLK1.3T (72323512360) Nibbler View Diagrams & Manuals
BLK1.3CS (72323612363) Nibbler View Diagrams & Manuals
FMM250Q (72293724110) MultiMaster View Diagrams & Manuals
FMM250Q (72293700360) Multi Master Oscillating Tool View Diagrams & Manuals
72292600115 Power Tool View Diagrams & Manuals
72293600360 Power Tool View Diagrams & Manuals
72302600117 Power Tool View Diagrams & Manuals
72302600621 Power Tool View Diagrams & Manuals
72302900115 Power Tool View Diagrams & Manuals
72302900629 Power Tool View Diagrams & Manuals
72323809360 Power Tool View Diagrams & Manuals
72323909360 Power Tool View Diagrams & Manuals
72324009360 Power Tool View Diagrams & Manuals
72324109360 Power Tool View Diagrams & Manuals
72324209360 Power Tool View Diagrams & Manuals
Show More Compatible Models
Don't see yours? Try searching our site for :

This item works with the following types of products:

  • Shear Parts
  • Nibbler Parts
  • Multi-Tool Parts

Repair Videos ?

Articles:
This article describes the differences between power switch and carbon brush failure symptoms....
September 18, 2009

Customer Part Reviews ?

5
Average Rating (out of 5):
7 Reviews
Click to filter by ratings:
5 stars
7
4 stars
0
3 stars
0
2 stars
0
1 stars
0
  • Highest Rating
  • Most Recent
< PREV
  • 1
NEXT >
  • Fixed problem works great
    Would not run replaced brushes and speed control works great like new osilating tool
    Bob - December 19, 2023 Verified Purchase
    Ereplacementparts has everything, good price
    Easy repair, great part
    Paul s - October 28, 2023 Verified Purchase
    Easy repair.Worked as expected.Thank you.
    Easy repair.Worked as expected.Thank you.
    DAVID - June 12, 2022 Verified Purchase
    Easy repair
    The brushes were worn out in my fein tool. Ordered and replaced them with the brushes I bought from ereplacement parts. Works great now
    Steve - January 26, 2021 Verified Purchase
    Easy fix with exact parts n
    Received the parts a lot quicker than expected. Which made me very happy, because I need to use this tool the next day.
    Guest - August 27, 2020 Verified Purchase
    New Life to a 10 year old tool
    The variable speed module went out on my Fein Multi tool The parts were easy to order and thinking while I have this thing apart I may as well replace the brushes... Parts came, Parts are in, Runs perfectly, Happy Camper.
    Guest - August 3, 2019 Verified Purchase
    Fein brush replacement
    Easy to replace and tool is back at full speed
    Bob - June 18, 2019 Verified Purchase
    t
    t
    t - t days ago Verified Purchase
    eReplacementParts Team
    t

    Questions & Answers ?

    Our customer Service team is at the ready daily to answer your part and product questions.

    photo of team member
    Ask our Team

    We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

    Does this fit my product?

    Questions & Answers for Carbon Brush


    No questions have been asked yet

    Customer Repair Instructions ?

    All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

    Easy 15-30 minutes (13 rated repairs)?

    No power, brushes worn

    ted - January 5, 2016
    👍 5 of 5 people found this instruction helpful
    Tool Type

    Nibbler

    Difficulty

    Medium

    Time

    15-30 minutes

    Tools Used

    Screwdriver, Pliers

    Removed lower cover to be able to get to the brushes, unhooked brushes connections. Pulled springs back holding the brushes in, then installed the new brushes.Replaced the lower cover.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Fein tool started working intermittently and then stopped altogether

    Glen - March 13, 2018
    👍 2 of 2 people found this instruction helpful
    Tool Type

    Oscillating Tool

    Difficulty

    Easy

    Time

    30-60 minutes

    Tools Used

    Screwdriver, Pliers, T-15 T-handle wrench

    I replaced both the brushes as well as the electronic module and the tool still did not work so I disasembled it again and cleaned the copper contacts on the armature by polishing off the build-up of carbon residue, (blackened looking stripe) using some BRASSO metal polish and some clean 3x3 gun cleaning patches. I followed that up by using some CRC electrical spray cleaner to clean out the spaces/slits between the contacts. Put it back together and it runs like new.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Intermittent power

    William - December 7, 2016
    👍 1 of 1 people found this instruction helpful
    Tool Type

    Oscillating Tool

    Difficulty

    Easy

    Time

    Less than 15 minutes

    Tools Used

    Screwdriver, Needle nose pliers

    1. Pulled cover off of motor
    2. Used awl to hold back spring tension on brushes
    3. Pulled off brush terminals with needle nose pliers and replaced both
    4. Be careful putting cover back on not to pinch brush wires feeds as they lie on outside edges.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Ran a little slow

    edward - December 5, 2023
    Tool Type

    Oscillating Tool

    Difficulty

    Easy

    Time

    Less than 15 minutes

    Tools Used

    Screwdriver

    Removed the plastic cover from the back, undid the brush holder screw, removed the wire from the connector. Then replaced everything, test ran the tool . All was good.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Stopped running

    James - November 17, 2022
    Tool Type

    Oscillating Tool

    Difficulty

    Medium

    Time

    15-30 minutes

    Tools Used

    Screwdriver

    Pulled cover, removed brushes. Found 1 brush holder was cracked. Replaced brush holder, installed 2 new brushes and good to go!
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Tool would not turn on.

    William - April 12, 2019
    Tool Type

    Oscillating Tool

    Difficulty

    Easy

    Time

    15-30 minutes

    Tools Used

    Screwdriver, Pliers

    I opened the case, 4 Phillips screws
    Removed and installed new switch, small Phillips screw driver.
    Installed new brushes..
    Closed case
    Did not use the brush holders, put in spare parts
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Brushes were bad

    Jason - May 7, 2018
    Tool Type

    Oscillating Tool

    Difficulty

    Easy

    Time

    15-30 minutes

    Tools Used

    , Torx wrench

    Changed brushes
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Occasionally tool would not turn on high speed

    Steve - August 7, 2017
    Tool Type

    Oscillating Tool

    Difficulty

    Easy

    Time

    15-30 minutes

    Tools Used

    Screwdriver

    Removed the lower cover
    Removed the wires from the old controller one at a time and connected them to the new controller
    Removed the brushes from the brush holder connections and connected the new ones
    Replaced the lower cover
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Brushes worn

    chris - May 15, 2017
    Tool Type

    Oscillating Tool

    Difficulty

    Easy

    Time

    Less than 15 minutes

    Tools Used

    Pliers, Torx driver set

    Removed the bottom cover of the tool
    Disconnect the old brush terminals
    Pull the end of the spring out from the holder and place it to the side
    Pull the old brushes out and install the new brushes
    Replace the brush holder spring
    Reconnect the brushes
    Replace the bottom cover
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Brushes worn out

    Jacques - April 5, 2017
    Tool Type

    Oscillating Tool

    Difficulty

    Easy

    Time

    Less than 15 minutes

    Tools Used

    Screwdriver

    Remove the lower cover assembly
    Disconnect the brushes
    Pull back on the brush springs, then remove the old brush and install the new brush
    Connect the new brushes
    Replace the lower housing
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.

    Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.

    Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

    All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.

    All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.

    Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.

    All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.

    This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.

    eReplacementParts.com
    7174 South 400 West
    Suite 5
    Midvale, UT 84047
    visa mastercard discover american express PayPal