Belt Poly-v Service E110538
Part Number: E110538
Order within the next 12 hours
and your part ships today!
and your part ships today!
*This part replaces obsolete part #: BT004800AV.
Product Information
Description:
This is a genuine manufacturer supplied replacement drive belt. It is specially designed for Campbell Hausfeld air compressors. This is the main belt that connects the pump and the electric motor. Over time belts tend to stretch and wear out eventually requiring replacement. Please note, this includes one (1) rubber belt. To replace this drive belt you will only need a screwdriver. • Make sure to unplug the compressor • Remove the belt cover • Remove the old belt • Clean both drive pulleys • Install the new belt • Secure the cover with the screws • Power the compressor and test the new belt |
Frequently Purchased With
Compatibility
This part is compatible with the following machines:
the 14 compatible machines
Products Compatibility
This item works with the following types of products:
- • Compressor
Questions & Answers for Belt Poly-v Service
No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
1 of 1 people found this instruction helpful
Tool Type:
Pump
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Socket set, Wrench Set, Adjustable Wrench
Air compressor quit!
I replaced the comp pump,belt, and conversion kit for the unloaded valve. Put synthetic mobile 1 in the compressor pump a 10 w30 wait and it operated flawlessly and was quieter than the old pump which sustained a broken crankshaft but it ran for 23 years moderately to hard operation! Thx for the new parts! It was very affordable and cheaper than buying a new air compressor!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Compressor
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Socket set, Wrench Set, Nutdriver
Broken belt
1 loosened 4 bolts and slid motor forward
2 put on belt and Slid motor back
3 took two blocks of wood one square one tapered (no way to tighten belt) hammered tapered block in until belt tightened without slipping
4 tightened four bolts replaced shields
2 put on belt and Slid motor back
3 took two blocks of wood one square one tapered (no way to tighten belt) hammered tapered block in until belt tightened without slipping
4 tightened four bolts replaced shields
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Compressor
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Wrench Set, Pry bar
Belt was coming apart
Replaced belt
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Compressor
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Wrench Set
Broken belt
Loosened motor mount
Installed belt
Tightened belt
Retightened motor
Installed belt
Tightened belt
Retightened motor
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Compressor
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Belt broke
Removed shield, installed new belt, tightened belt and reinstalled shield.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Compressor
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Socket set, Wrench Set, Pry bar
Belt broke after 20 plus years
Remove shroud
Loosen motor bolts
Replace belt
Tension belt by adjusting motor position
Tighten bolts
Replace fan shroud
Loosen motor bolts
Replace belt
Tension belt by adjusting motor position
Tighten bolts
Replace fan shroud
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Compressor
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Wrench Set, Wheel puller
Retaining bolt on motor pulley loosened allowing pulley to slide on shaft and become misaligned with compressor pulley. This misalignment caused the belt to jump off pulley and tear.
1. Remove belt shroud.
2. Loosen motor pulley lock bolt completely.
3. Apply gear/wheel pulley and pull pulley into alignment with compressor pulley.
4. Check alignment with straight edge.
5. Tighten lock bolt.
6. Loosen motor mount bolts and side motor toward compressor.
7. Install belt, slide motor to tighten belt, tighten mount bolts and install belt shroud.
2. Loosen motor pulley lock bolt completely.
3. Apply gear/wheel pulley and pull pulley into alignment with compressor pulley.
4. Check alignment with straight edge.
5. Tighten lock bolt.
6. Loosen motor mount bolts and side motor toward compressor.
7. Install belt, slide motor to tighten belt, tighten mount bolts and install belt shroud.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
0 of 1 people found this instruction helpful
Tool Type:
Compressor
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Broken belt
Remove belt guard from compressor. The just work belt on to pulleys. Replace the belt guard.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
7 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
6
4 stars
1
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
East repair.
The replace poly-v belt fit perfectly and my air compressor is back in service. Thanks for the quick response and delivery.
Guest -
August 8, 2022
Verified Purchase
great customer service, sorry i can't remember his name, super helpful, very knowledgeable.
Living in the US Virgin Islands, couldn't believe how quickly I received it.
Your company is my "first to go to" with any parts I need. I'm a small marine mechanical repair business.
Thank you so much eReplacementParts!!
Guest -
December 14, 2020
Verified Purchase
Air compressor belt
Very happy with the customer service. The belt arrived within a week. It fit perfectly & the compressor works great. I would definitely recommend your company.
Guest -
May 6, 2020
Verified Purchase
Great part
Very satisfied
WILLIAM -
December 7, 2019
Verified Purchase
Correct part
The correct belt to replace the worn part.
Guest -
October 3, 2019
Verified Purchase
Worked as expected
Arrived quickly fit as expected reasonable price
Guest -
June 19, 2019
Verified Purchase
Great part
Perfect replacement part for my compressor
Guest -
October 3, 2019
Verified Purchase
Verified Purchase
eReplacementParts Team
< PREV
- 1
Product Information