Belt Hook 42-70-5150
Part Number: 42-70-5150
Order within the next 10 hours
and your part ships today!
and your part ships today!
Product Information
Description:
The Milwaukee Belt Hook is attached to the bottom of the handle assembly on the tool model numbers shown below. Its purpose is to hook the tool to your belt when not using the tool. To attach the belt hook to the handle you will also need to order part number 06-82-5275 Screw. |
Frequently Purchased With
Compatibility
the 21 compatible machines
This part is compatible with the following machines:
Milwaukee
2601-20 (SER B28A) 1/2" Compact Driver Drill
2650-20 (SER B55A) 18 Volt 1/4" Hex Impact Driver
2650-21 (SER B55A) 18 Volt 1/4" Hex Impact Driver
2650-22 (SER B55A) 18 Volt 1/4" Hex Impact Driver
2601-22 (SER B28A) 1/2" Compact Driver Drill
2651-20 (SER B77A) 18 Volt 3/8" Square Impact Driver
2651-22 (SER B77A) 18 Volt 3/8" Square Impact Driver
2652-20 (SER B78A) 18 Volt 1/2" Square Impact Driver
2652-22 (SER B78A) 18 Volt 1/2" Square Impact Driver
2601-20 (B28B) 1/2" Compact Driver Drill
2601-20 (B28C) 1/2" Compact Driver Drill
2650-20 (SER B55A) 18 Volt 1/4" Hex Impact Driver
2650-21 (SER B55A) 18 Volt 1/4" Hex Impact Driver
2650-22 (SER B55A) 18 Volt 1/4" Hex Impact Driver
2601-22 (SER B28A) 1/2" Compact Driver Drill
2651-20 (SER B77A) 18 Volt 3/8" Square Impact Driver
2651-22 (SER B77A) 18 Volt 3/8" Square Impact Driver
2652-20 (SER B78A) 18 Volt 1/2" Square Impact Driver
2652-22 (SER B78A) 18 Volt 1/2" Square Impact Driver
2601-20 (B28B) 1/2" Compact Driver Drill
2601-20 (B28C) 1/2" Compact Driver Drill
2650-20 (B55B) 18 Volt 1/4" Hex Impact Driver
2651-20 (B77B) 18 Volt 3/8" Square Impact Driver
2652-20 (B78B) 18 Volt 1/2" Square Impact Driver
2601-20 (SER B28D) 1/2" Compact Driver Drill
2601-059 (SER D36A) 1/2" Compact Driver Drill
2601-059 (SER D36C) 1/2" Compact Driver Drill
2650-20 (B55C) 18 Volt 1/4" Hex Impact Driver
2601-21 1/2" Compact Driver Drill
2602-22DC M18 1/2" Compact Hammer Drill
2602-22DC M18 1/2" Compact Hammer Drill
2651-20 (B77B) 18 Volt 3/8" Square Impact Driver
2652-20 (B78B) 18 Volt 1/2" Square Impact Driver
2601-20 (SER B28D) 1/2" Compact Driver Drill
2601-059 (SER D36A) 1/2" Compact Driver Drill
2601-059 (SER D36C) 1/2" Compact Driver Drill
2650-20 (B55C) 18 Volt 1/4" Hex Impact Driver
2601-21 1/2" Compact Driver Drill
2602-22DC M18 1/2" Compact Hammer Drill
2602-22DC M18 1/2" Compact Hammer Drill
Products Compatibility
This item works with the following types of products:
- • Drill
- • Hammer Drill
- • Impact Driver
Questions & Answers for Belt Hook
No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
Tool Type:
Impact Driver
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers, Soldering iron
Brushes where worn, would not turn motor
1. Removed case screws
2. Disassembled tool case
3. De solder brush pack
4 Re solder new brush pack
5. Re assemble case
6 Reinstall case screws
7. Check for proper function
2. Disassembled tool case
3. De solder brush pack
4 Re solder new brush pack
5. Re assemble case
6 Reinstall case screws
7. Check for proper function
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Cordless Drill
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Allen wrench and hammer soldering gun
Chuck Assembly was wobbling, Brush Card Assembly was bad it was smoking, added bit holder and belt hook
Removed Chuck Assembly screw with screwdriver and put allen wrench in Chuck Assembly put drill in low gear smacked allen wrench with hammer Chuck Assembly came right off.
Removed back of drill for Brush Card Assembly then opened drill shell unsoldered two wires from trigger soldered in the two wires on the new Brush Card Assembly reassembled drill shell put new Chuck Assembly on in reverse order, added Belt Hook with one Pan Head Screw and bit holder with one Pan Head Screw.
Removed back of drill for Brush Card Assembly then opened drill shell unsoldered two wires from trigger soldered in the two wires on the new Brush Card Assembly reassembled drill shell put new Chuck Assembly on in reverse order, added Belt Hook with one Pan Head Screw and bit holder with one Pan Head Screw.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
1 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
1
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
fit perfectly and arrived on time
What a great addition to my impact drill. Can't believe I went so long without one of these
Guest -
November 26, 2019
Verified Purchase
Verified Purchase
eReplacementParts Team
< PREV
- 1
Product Information