
We Sell Only Genuine Andis® Parts.
Andis Clipper Parts & Models
Popular Andis Clipper Parts

Genuine Andis replacement part, this item is sold individually.
The purpose of the 26899 Screw is to secure the Blade to the Clipper/Trimmer model numbers shown below.
Two of the screws are needed on each model.

This is an OEM part from Andis. The Blade Drive is used on many Andis clippers. This part is used to drive the cutter on the blades to cut hair. This part should be replaced if any of the flexible tabs have broken loose or if the tip has worn out. Included with this part is instructions on how to correctly replace the Blade Drive.
Tools used:
• Philips Head Screw Drivers
• Flat Head Screw Drivers (To help pry old part off)

This is a Genuine Manufacturer Sourced replacement part used on a Andis Clippers. This item is made from Nylon and it is Sold Individually. The purpose of the Blade Guide is to keep tension on the blade, and keep the tension spring from rubbing metal to metal on the blade. This which will make your blades last longer.
Please note: It is important to fit the Blade Guide completely over the tension spring, otherwise it may cause the cutter blade to not cut correctly.

This part comes directly from Andis. This Blade Lock is used on many Andis clippers. This part is black and made of metal. It is used to hold and lock the blades into place. It is common for the hooked tip to break after a time. It is recommended to purchase a couple of these Locks at one time. The Lock is easy to replace. Remove the two Philips Head Blade Hinge Screws (part number 27864). Remove the Hinge Assembly (S63897) and align the spring with the holes on the new Lock and reinstall.
Tools Used:
• Screw Driver

This is a genuine OEM sourced replacement part designed for use with Andis clippers. This assembly includes one (1) carbon brush with a lead wire attached. Please note brush spring and retaining clip are both sold separately.
Due to normal use and friction brushes will gradually wear down and will require replacement. It is advised to replace both brushes at the same type.
You would need a screwdriver to complete this job.
• Make sure the unit is unplugged
• First remove cover
• Take our old brushes and replace them with the new ones
• Secure the cover and test the tool

This part comes directly from Andis. The Foam Pad is used in many models of Andis hair clippers. The Pad is made of a light foam and includes an adhesive backing. The Pad is used to help prevent hair and debris from getting into the motor. It attaches to the Drive Cap. The pad should be replaced if it gets full of hair or if the adhesive backing no longer sticks. No tools are used to replace this part.

Genuine Andis replacement part, this item is sold individually.
The purpose of the 26899 Screw is to secure the Blade to the Clipper/Trimmer model numbers shown below.
Two of the screws are needed on each model.

This is an OEM part from Andis. The Blade Drive is used on many Andis clippers. This part is used to drive the cutter on the blades to cut hair. This part should be replaced if any of the flexible tabs have broken loose or if the tip has worn out. Included with this part is instructions on how to correctly replace the Blade Drive.
Tools used:
• Philips Head Screw Drivers
• Flat Head Screw Drivers (To help pry old part off)

This is a Genuine Manufacturer Sourced replacement part used on a Andis Clippers. This item is made from Nylon and it is Sold Individually. The purpose of the Blade Guide is to keep tension on the blade, and keep the tension spring from rubbing metal to metal on the blade. This which will make your blades last longer.
Please note: It is important to fit the Blade Guide completely over the tension spring, otherwise it may cause the cutter blade to not cut correctly.

This part comes directly from Andis. This Blade Lock is used on many Andis clippers. This part is black and made of metal. It is used to hold and lock the blades into place. It is common for the hooked tip to break after a time. It is recommended to purchase a couple of these Locks at one time. The Lock is easy to replace. Remove the two Philips Head Blade Hinge Screws (part number 27864). Remove the Hinge Assembly (S63897) and align the spring with the holes on the new Lock and reinstall.
Tools Used:
• Screw Driver

This is a genuine OEM sourced replacement part designed for use with Andis clippers. This assembly includes one (1) carbon brush with a lead wire attached. Please note brush spring and retaining clip are both sold separately.
Due to normal use and friction brushes will gradually wear down and will require replacement. It is advised to replace both brushes at the same type.
You would need a screwdriver to complete this job.
• Make sure the unit is unplugged
• First remove cover
• Take our old brushes and replace them with the new ones
• Secure the cover and test the tool

This part comes directly from Andis. The Foam Pad is used in many models of Andis hair clippers. The Pad is made of a light foam and includes an adhesive backing. The Pad is used to help prevent hair and debris from getting into the motor. It attaches to the Drive Cap. The pad should be replaced if it gets full of hair or if the adhesive backing no longer sticks. No tools are used to replace this part.