Armature With Bearing And Fan 515611-3
Part Number: 515611-3
Order within the next 31 minutes
and your part ships today!
and your part ships today!
Product Information
Description:
Original OEM replacement Armature Assembly used on some Makita Angle Grinders. This item includes an Armature, Fan, Commutator End Bearing. Remember to be especially careful of the armature fan when you remove it, because if you break it, you will have to replace the entire armature. Due to constant contact with Carbon Brushes armature will eventually wear out and would need to be replaced. It is highly recommended to replace both Carbon Brushes when replacing an armature. |
Frequently Purchased With
Compatibility
This part is compatible with the following machines:
Products Compatibility
This item works with the following types of products:
- • Grinder
Repair Guides
Articles:
Grinder stopped working? Step-by-step instructions show you how to remove and install the armature on your Makita grinde...
November 11, 2015
|
Questions & Answers for Armature With Bearing And Fan
No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
6 of 7 people found this instruction helpful
Tool Type:
Grinder
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers
Grinder had an arch at the brushes
I watched your you tube video on how to do this repair, thank you. Here is a copy of it if you have the same problem. https://www.youtube.com/watch?v=cUXQEtNUpJE
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 3 people found this instruction helpful
Tool Type:
Grinder
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Adjustable Wrench
Slow RPM , no power. Could not see any arcing
Took out screws in handle.
Removed brushes.
Removed 4 screws holding head on. Slid out armature from body.
Held armature with hand using adjustable wrench to remove nut then gear.
Assembled in reverse order.
Removed brushes.
Removed 4 screws holding head on. Slid out armature from body.
Held armature with hand using adjustable wrench to remove nut then gear.
Assembled in reverse order.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Grinder
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers, Wrench Set
broken carbon brush and burnt armature
Removed the grinder casing, removed burnt armature and replaced with the new one, dropped the new carbon brush in place of the broken one,. Installed the body casing , head and a few screws and it run like the day it was purchased. Thanks eReplacementParts.com! I will be a repeat customer...
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Grinder
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Nothing
Was just easy to work on and the parts were exactly the right ones. Thanks
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Grinder
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
The armature went out along with the brushes
I just watched the video on your you tube channel. It was very easy.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Grinder
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers, bearing puller
grinder worked slowly and without force
1.removing the screws from the cover that covers the switch and brushes
2. remove the brushes
3. Remove the 4 screws from the transmission to the electric motor
4. replace and install the rotor, bearing, plate...
5. Assemble everything and probe
6.100% perfect new tool
2. remove the brushes
3. Remove the 4 screws from the transmission to the electric motor
4. replace and install the rotor, bearing, plate...
5. Assemble everything and probe
6.100% perfect new tool
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Grinder
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Small pick tool
intermittent running, noisy
Removed rear cover (1 screw), removed angled drive head and pinion gear (4 screws), removed brushes (pick), removed armature from large bearing housing, removed small bearing cover (important, as it was stuck inside the tool body), reinstalled large bearing and housing on new armature, installed bearing cover on small bearing, reinstalled assembly into tool body, reattached angled drive head and pinion gear, installed new brushes... fired right up, no issues.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
5 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
5
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
works great!
I REPAIRED THE ANGLE GRINDER WITH O.E.M. PARTS I PURCHASED FROM
E-REPLACEMENT, AND WILL PURCHASE POWER TOOL PARTS IN THE FUTURE.
Guest -
May 15, 2022
Verified Purchase
Easy installation..fantastic faq section so I knew exactly what parts I needed
10/10
Guest -
July 8, 2020
Verified Purchase
Replacement armature
The armature works great, it arrived in about a week. I am very happy with this product.
Guest -
May 19, 2020
Verified Purchase
Easy repair, works great
My grinder runs like new again!
Hoskie -
December 18, 2019
Verified Purchase
Part was awesome, easy to replace, worked as expected.
The part was well packaged and arrived intact ,awesome to be able to purchase a complete unit , ie,armature with bearing and fan.
iGlobal -
September 10, 2019
Verified Purchase
Verified Purchase
eReplacementParts Team
< PREV
- 1
Product Information
Repair Guides
Articles:
Grinder stopped working? Step-by-step instructions show you how to remove and install the armature on your Makita grinde...
November 11, 2015
|