Carbon Brush With Spring 22-18-0670
and your part ships today!
|
This is a genuine Milwaukee replacement part, it is sold individually. 2 of these Brushes are required in the tool listed below. It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems. |
This part is compatible with the following machines:
4240 (SER 751-1001) Electric Drill
4245 (SER 782-1001) Electric Drill
4245 (SER 782-1001) Electric Drill
4245 (SER 782-2369) Electric Drill
4245 (SER 782-2369) Electric Drill
6230 (SER 678-26651) 4-3/4 Inch Deep Cut Band Saw
6230 (SER 678-26651) 4-3/4 Inch Deep Cut Band Saw
6230 (SER 678-31501) 4-3/4 Inch Deep Cut Band Saw
6230 (SER 678-31501) 4-3/4 Inch Deep Cut Band Saw
6230 (SER 678-32001) 4-3/4 Inch Deep Cut Band Saw
6230 (SER 678-32001) 4-3/4 Inch Deep Cut Band Saw
6230 (SER 678A) 4-3/4 Inch Deep Cut Band Saw
6230 (SER 678A) 4-3/4 Inch Deep Cut Band Saw
6230 (SER 678B) 4-3/4 Inch Deep Cut Band Saw
6230 (SER 678B) 4-3/4 Inch Deep Cut Band Saw
6230 (SER 678C) 4-3/4 Inch Deep Cut Band Saw
6230 (SER 678C) 4-3/4 Inch Deep Cut Band Saw
6230 (SER 678D) 4-3/4 Inch Deep Cut Band Saw
6230 (SER 678D) 4-3/4 Inch Deep Cut Band Saw
6236 (SER 769-1001) Two Speed Deep Cut Bandsaw
6236 (SER 769-1001) Two Speed Deep Cut Bandsaw
6236 (SER 769-1901) Two Speed Deep Cut Bandsaw
6236 (SER 769-1901) Two Speed Deep Cut Bandsaw
6236 (SER 769A) Two Speed Deep Cut Bandsaw
6236 (SER 769A) Two Speed Deep Cut Bandsaw
6236 (SER 769B) Two Speed Deep Cut Bandsaw
6236 (SER 769B) Two Speed Deep Cut Bandsaw
6236 (SER 769C) Two Speed Deep Cut Bandsaw
6236 (SER 769C) Two Speed Deep Cut Bandsaw
6236 (SER 769D) Two Speed Deep Cut Bandsaw
6236 (SER 769D) Two Speed Deep Cut Bandsaw
6236 (SER 769E) Two Speed Deep Cut Bandsaw
6236 (SER 769E) Two Speed Deep Cut Bandsaw
6236 (SER 769F) Two Speed Deep Cut Bandsaw
6236 (SER 769F) Two Speed Deep Cut Bandsaw
1675-1 (SER 413-336097) Two Speed Hole Hawg Drill
1670-1 (SER 472-23375) Single Speed Hole Hawg Drill
1670-1 (SER 472-24725) Single Speed Hole Hawg Drill
1670-1 (SER 472-25501) Single Speed Hole Hawg Drill
1670-1 (SER 472A) Single Speed Hole Hawg Drill
1670-1 (SER 472B) Single Speed Hole Hawg Drill
1670-1 (SER 472C) Single Speed Hole Hawg Drill
1675-1 (SER 413-314575) Two Speed Hole Hawg Drill
1675-1 (SER 413-347251) Two Speed Hole Hawg Drill
1675-1 (SER 413A) Two Speed Hole Hawg Drill
1675-1 (SER 413B) Two Speed Hole Hawg Drill
1675-1 (SER 413C) Two Speed Hole Hawg Drill
1675-1 (SER 413D) Two Speed Hole Hawg Drill
1678-20 (SER 930A) Electric Drill / Driver
1678-20 (SER 930A) Electric Drill / Driver
1679-01 (SER 915A) Electric Drill / Driver
1679-01 (SER 915A) Electric Drill / Driver
6227 (SER 674A) Bandsaw
6227 (SER 674A) Bandsaw
6225 (SER 457B) Bandsaw
6225 (SER 457B) Bandsaw
6227 (SER 674-23301) Bandsaw
6227 (SER 674-23301) Bandsaw
6225 (SER 457-222501) Two Speed Band Saw
6225 (SER 457-222501) Two Speed Band Saw
6225 (SER 457-242250) Two Speed Band Saw
6225 (SER 457-242250) Two Speed Band Saw
6225 (SER 457A) Two Speed Band Saw
6225 (SER 457A) Two Speed Band Saw
6223 (SER 822A) Band Saw
6223 (SER 822A) Band Saw
6223 (SER 822B) Band Saw
6223 (SER 822B) Band Saw
6223 (SER 822C) Band Saw
6223 (SER 822C) Band Saw
6223 (SER 822D) Band Saw
6223 (SER 822D) Band Saw
6223 (SER 822E) Band Saw
6223 (SER 822E) Band Saw
6227 (SER 674-25901) Speed Control Bandsaw
6227 (SER 674-25901) Speed Control Bandsaw
6227 (SER 674-27001) Speed Control Bandsaw
6227 (SER 674-27001) Speed Control Bandsaw
6227 (SER 674B) Speed Control Bandsaw
6227 (SER 674B) Speed Control Bandsaw
6227 (SER 674C) Bandsaw
6227 (SER 674C) Bandsaw
1670-1 (SER 472E) Single Speed Hole Hawg Drill
1675-1 (SER 413E) Two Speed Hole Hawg Drill
This item works with the following types of products:
- • Band Saw
- • Drill
- • Electric Drill
- • Saw
Step-by-step instructions for removing and installing the carbon brushes on your Milwaukee Hole Hawg....
March 19, 2018
|
Questions & Answers for Carbon Brush With Spring
1. take handle apart to access the switch and wiring of the fields and brush holders to the switch.
2. take motor housing rear bonnet off to gain access to fields and brush holders.
3. remove armature to get access to removing fields.
4. two screws hold fields in place, removing them and pulling fields from housing noting where field wires go.
5. you can now take brush holders out. there is a right and a left holder, take note where and the lead that is connected to it.
6. reverse order to put in new parts and installing brushes.
7. a lot of times i take pictures to remember where wiring goes and go to manufacturing web site to see exploded view of unit.
Unscrew remove cover for brushes
Removed old brushes
Put in new brushes
Screwed brush cover back on
fit in the brush holders. I had to sand off
about 1/8” from each side so they would
fit. Then I had to remove the spring , which
was too large in diameter and reuse the
original springs.
I could not wait to get the right brush-set
I had a job that needed to be completed.
The portable band saw works ok.
- 1
- 1
Step-by-step instructions for removing and installing the carbon brushes on your Milwaukee Hole Hawg....
March 19, 2018
|