Fw, .77x1.13x.06 7010935SM

Description:

The metal flat washer is priced individually. It attaches to the cast iron axle along with the bolt and the bearing. A set of pliers, a screwdriver, and a wrench may be necessary during the installation of this item. This is an original part for Murray lawn tractors and Snapper rear engine rider mowers.

Frequently Purchased With

Bearing
$4.99

Bearing, Flang..
$8.25

Seal, Felt
$5.18

Retainer, Ring..
$4.99

Hub Cap
$4.99

Washer, Spindl..
$7.84

Bearing, Ball..
$12.07

Cap, Dust, Yel..
$4.99

Compatibility

This part is compatible with the following machines:

Murray

7800409 (ELT125380) Lawn Tractor
7800412 (EYK125380) Lawn Tractor
7800410 (ELT155420G) Lawn Tractor
7800411 (ELT155420H) Lawn Tractor
7800413 (EYK155420G) Lawn Tractor
7800414 (EYK155420H) Lawn Tractor
7800497 (ELB155420H) Lawn Tractor
7800399 (ELT175460H) Lawn Tractor
7800400 (ELT12460H) Lawn Tractor
7800416 (EYK12460H) Lawn Tractor

7800498 (ELB175460H) Lawn Tractor
7800162 (LT155420) Lawn Tractor
7800191 (LT185420) Lawn Tractor
7800307 (CLT155420) Lawn Tractor
7800309 (CLT185420) Lawn Tractor
7800361 (LT135420C) Lawn Tractor
7800362 (LT155420C) Lawn Tractor
7800370 (FLT185420) Lawn Tractor
7800192 (LT20460) Lawn Tractor
7800311 (CLT20460) Lawn Tractor

Snapper

Expand the 150+ compatible machines

Products Compatibility

This item works with the following types of products:

• Lawn Tractor
• Snowblower

Repair Instructions: Submitted by Customers Like You

Tool Type:

Lawn Tractor

Parts Used:

Fw, .77x1.13x.06 - 7010935SM

Bearing - 7010986YP

Bushing, 3/4 Steering Shaft - 7019166YP

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Pliers, Snap ring pliers, punch,hammer,end cutting pliers for cotter

Too much slack in front end and steering parts

Took off front tire after I jacked it up, replaced cotter pins, replaced old grease with new one for bearing. Knocked out the bushing and replaced with new one, added shimm washer to make tires fit properly on axle. Done same thing on the other side. Replace steering wheel bushing with new one. Adding shims to it to make it tighter also. Grease up outer bearings on both sides, finish up job and put mower back on ground.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Tractor

Parts Used:

Fw, .77x1.13x.06 - 7010935SM

Bearing, Flange Ball - 7011807YP

Cap, Dust, Yellow - 7031038YP

Seal, Felt - 7011032YP

Hub Cap - 7011022YP

Tie-rod - 7024935YP

Repair Difficulty:

Easy

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Pliers, Wrench Set, hammer

Tie rod end worn out (came apart) and bearings worn.

1. Jacked up front end of mower.
2. removed nuts/washers from tie rod ends.
3. Replaced new tie rods with old nuts/washers.
4. Removed hub caps from front wheels and cleaned off excess grease.
5. Removed cotter pin, washer, wheel, inner washers, seal, and cap dust cover.
6. Removed inner and outer bearings with screw driver and hammer.
7. Replaced bearings and put everything back in reverse order.
8. Added grease to wheels between the bearings and replaced the hub caps.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Mower

Parts Used:

Fw, .77x1.13x.06 - 7010935SM

Bearing, Flange Ball - 7011807YP

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Pliers, Hammer

Wheel bearing broke

Pulled the cotter pen
remove the wheel
used screwdriver and hammer to pop out the old bearings
cleaned out old grease
used a hammer and block of wood to hammer in new bearings
re-attached the wheel
grease hub

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Tractor

Parts Used:

Fw, .77x1.13x.06 - 7010935SM

Fw, .766x1.310x.06 Yz - 7029617YP

Cap, Dust, Yellow - 7031038YP

Bearing, Wheel - 7014483YP

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver, Pliers, Socket set, hammer and large flat screwdriver

Front wheel bearing worn out

removed front left wheel
removed worn bearings using hammer and large screwdriver for one bearing, socket with extension for the second.
installed new bearings
reinstalled wheel with new washers to get correct spacing on axle
greased axle using grease gun
tested

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Snowblower

Parts Used:

Fw, .77x1.13x.06 - 7010935SM

Bearing, Ball - 2108202SM

Worm Gear Asmy - 7051305YP

Washer - 7014296YP

Bearing - 7013924YP

Plate, Drive - 7051358YP

Bearing, Ball - 7014295YP

Seal, 1-1/2 O.d. Oil - 7013858YP

O-ring, Case Cover - 7013854YP

Shaft, Impeller - 7027630YP

Spacer, Gear Bearing - 7013856YP

Gear, Rolled Worm - 7027606YP

Bearing, PM - 7012252YP

O-ring, Case Cap - 7013853YP

Washer, Thrust - 7013855SM

Repair Difficulty:

Hard

Time Spent Repairing:

More than 2 hours

Tools Used:

Screwdriver, Pliers, Socket set, Wrench Set, Nutdriver, Adjustable Wrench, Rosebud, 2# hammer, punches,welder. angle grinder

Snowblower was 32 years old, lots of rust and wear on the impeller shaft making it difficult to remove. Small cracks on frame, and augers.

1. Removed engine and belts.
2. Removed wheels, axle shaft and flanged bushings.
3. Removed Murray drive clutch and hex shaft.
4. Disassembled pulleys and bearings from impeller shaft.
5. Had to use a cut off blade on 4" angle grinder and cut shaft in 4 pieces to remove worm drive, augers and second stage impeller.
6. Rebuilt worm drive.
7. Welded all minor cracks.
8. Straighten bent augers and 2nd stage impeller.
9. Reassembled snowblower which was very easy with the new parts.
10. While the snow blower was apart I took the opportunity to clean and repaint all parts.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Lawn Tractor

Parts Used:

Fw, .77x1.13x.06 - 7010935SM

Bearing - 7010986YP

Bearing - 7013321YP

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Pliers, Electric wrench for tire removal and snap ring pliers

Snapper riding mower had to much play in the steering

1. Remove both front tires
2. Remove all cotter keys from steering parts
3. Remove snap-rings from both spindles
4. Install new bearings, 8, in spindles and tie rod ends
5. This tightened up the steering

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Reviews

Average Rating (out of 5):

2 Reviews

Click to filter by ratings:

5 stars

2

4 stars

0

3 stars

0

2 stars

0

1 stars

0

Sort by:

Highest Rating
Most Recent

< PREV

1

NEXT >

Part worked perfectly

All I had to do was input the model number and was directed to the list of parts I needed. Parts fit perfectly and repairs went smoothly. Thanks

Guest - August 3, 2021 Verified Purchase

The product was received very prompt.

The part was perfect and is now ready to mow.

Guest - August 9, 2019 Verified Purchase

Verified Purchase

eReplacementParts Team

Sort by:

Highest Rating
Most Recent

< PREV

1

NEXT >

Fw,​​ .​​77x1.​​13x.​​06 7010935SM

Questions & Answers for Fw,​ .​77x1.​13x.​06

Questions & Answers for Fw, .77x1.13x.06