This is an authentic Char-Broil replacement part, it is sold individually. Includes screw.
This is the part of the Grill where the flame originates from.
Depending on your grill you may have 3 or 4 of these.
To connect these to your grill, place the flat side of the Burner in the rear side of the firebox in the slots provided.
The front of the burner will connect to the Electrode w/ Wire/Collector.
They will connect to the Hose Valve Regulator, and then the Control Knobs will be attached, so the flame can be controlled.
Compatible with the Grills listed below.
Burner Tube G560-5800-W1A
OEM part for: Char-Broil
Part Number: G560-5800-W1A
Jump To:
Product Description ?
- Approx. 18.8" L
- Classification: Part
- Weight: 0.59 lbs.
- Shipping: Ships Worldwide
Frequently Purchased Together ?
Compatibility
This part will fit the following 2 machines
Char-Broil
This item works with the following types of products:
This part replaces obsolete part #: G560-6000-W1A, G560-6000-W1, G560-5800-W1
Repair Videos ?
Having trouble getting your grill to light up? A common cause of this issue is a defective ignition switch. We'll sho...
November 08, 2012
|
Customer Part Reviews ?
- 1
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Burner Tube
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Most difficult was getting the rusted screws and nuts loose to free the burner tubes and electrode igniter.
Tool Type
Outdoor Grill
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver, Wrench Set
Parts Used
Whole burner assembly was rusted starter tube broke in half.
Tool Type
Outdoor Grill
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver, Power Drill, Wrench Set
Rusted gas tubes and carry-over tubes.
Tool Type
Outdoor Grill
Difficulty
Easy
Time
30-60 minutes
Tools Used
Screwdriver
2. Unscrewed gas tubes and carry-over tubes.
3. Removed tubes. Gas tube removal is a little awkward, but tubes can be pulled out from firebox with some persistence. Electrode must be unscrewed and removed from the gas tube.
4. Inserted new tubes into the valves on one end and secured opposite end with screws. Reattached electrode to gas tube.
5. Attached carry-over tubes to gas tubes.
6. Replaced cooking grates.
7. Installed grease clip and cup.
Burner tubes and carry-over tubes rusted out
Tool Type
Outdoor Grill
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver, Power Drill, Wrench Set
2) Drilled out rusted and stuck screws holding burner and carry-over tubes.
3) Removed old burner and carry-over tubes.
4) Disconnected igniter from the one burner tube ( this grill only has one igniter ).
5) Connected igniter to new burner tube, positioned all burner tubes.
6) Installed new burner tube bolts, washers, and nuts, and tightened them.
7) Installed new carry-over tubes and tightened their screws.
8) Tested all burners to ensure proper operation.
9) Reinstalled flame tents and grills.
Old burners rusted out.
Tool Type
Outdoor Grill
Difficulty
Medium
Time
15-30 minutes
Tools Used
Power Drill
Parts Used
All 4 burners were rusted out.
Tool Type
Outdoor Grill
Difficulty
Easy
Time
30-60 minutes
Tools Used
Screwdriver, Pliers, Small grinder
2. Removed old burners.
3. Dropped in new burners.
4. Mounted the old igniter.
5. Mounted cross over tubes.
6. All new mounting hardware was provided. Works like new!
Burners were old and rusted
Tool Type
Outdoor Grill
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver, Pliers
Installed new burners and heat plates.
Burners in bad condition, crossover tubes rusted out as well as grease tray
Tool Type
Outdoor Grill
Difficulty
Hard
Time
1-2 hours
Tools Used
Screwdriver, Pliers, Power Drill
Parts worn out from use
Tool Type
Outdoor Grill
Difficulty
Easy
Time
30-60 minutes
Tools Used
Screwdriver, Socket set, Angle grinder
Corroded
Tool Type
Outdoor Grill
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Power Drill
Parts Used
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.