Genuine manufacturer-approved replacement switch which is specially produced for use with a Ridgid angle grinder. It is the part of the tool handling on/off and variable speed operations, over time either due to mechanical or electrical issue the switch may begin to fail eventually requiring replacement. Please note this high-quality plastic body item is sold individually.
Switch 760304012
OEM part for: Ridgid
Part Number: 760304012
Compatibility
This part will fit the following 1 machine
Ridgid
This item works with the following types of products:
- Grinder Parts
Customer Part Reviews ?
- 1
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Switch
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
trigger switch stopped working
Tool Type
Grinder
Difficulty
Easy
Time
15-30 minutes
Tools Used
, 2 torx scredrivers
Parts Used
1. Removed the old switch by loosening the four screws which secured the 4 wires and removed wires
2. Removed the old switch
3. Set the new one in place
4. Placed the 4 wires in the same locations as the old switch
5. Tightened screws
6. Reattached the halves of the grinder together using 2 screws
7 Replaced the brushes and then the caps
8. Plugged grinder into electricity
9 . Grinder worked so I unplugged grinder from electricity
10. Replaced the remainder of the screws and tested again.
It has been working as if it were new since I did the repair on the switch.
Grinder would not power on, used multimeter to test trigger switch which was bad.
Tool Type
Grinder
Difficulty
Easy
Time
15-30 minutes
Tools Used
, Torx Screw Drivers
Parts Used
2. Used T10 driver to remove 2 screws on head.
3. Separated body halves to access switch.
4. Removed old switch and connected wires using Phillips head screw driver to new switch (which was a perfect match).
5. Reversed steps to assemble.
6. Tested grinder and works perfectly.
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.