Repair Parts Home    Lawn Equipment Parts    Ryobi Parts    Ryobi Trimmer Parts    Ryobi RY30524 String Trimmer Parts
Ryobi RY30524 String Trimmer

 Ryobi RY30524 String Trimmer Parts

Upper Shaft Assembly
Engine Assembly
Lower Shaft Assembly
     
Upper Shaft Assembly
Click to close
 Fig # Img Part Name Availability Price
A1
Fuel Cap 2" Dia.
Fuel Cap 2" Dia.
Part #: 300758006
In stock
23 available
 $6.86
Add To Cart
A2
Model Label (CS30)
Part #: 985162001
Ships in 8 - 14 business days
 $0.99
Add To Cart
A3
Logo Plate
Logo Plate
Part #: 985157001
Ships in 8 - 14 business days
 $0.86
Add To Cart
A4
Spark Plug
Spark Plug
Part #: 870174001
In stock
25+ available
 $5.80
Add To Cart
A5
Starting Label
Starting Label
Part #: 940967004
In stock
5 available
 $3.99
Add To Cart
A6
Choke Label
Choke Label
Part #: 940330006
In stock
8 available
 $3.99
Add To Cart
A7
Choke Dial Cover
Choke Dial Cover
Part #: 518496002
In stock
2 available
 $1.96
Add To Cart
A8
Wavy Washer
Wavy Washer
Part #: 678434002
In stock
4 available
 $0.99
Add To Cart
A9
Washer
Washer
Part #: 678434001
In stock
3 available
 $3.99
Add To Cart
A10
Hex Nut (M4)
Hex Nut (M4)
Part #: 678435001
In stock
10 available
 $3.99
Add To Cart
A11
Control Handle Assembly
Control Handle Assembly
Part #: 000998236
In stock
2 available
 $12.76
Add To Cart
A12
Screw (10-14 x 1 in.)
Screw (10-14 x 1 in.)
Part #: 82589
In stock
10 available
 $1.99
Add To Cart
A13
Trigger Lock
Trigger Lock
Part #: PS06258
In stock
9 available
 $3.99
Add To Cart
A14
Trigger
Trigger
Part #: PS06259
In stock
13 available
 $3.99
Add To Cart
A15
Spring, Throttle
Spring, Throttle
Part #: UP03210
In stock
8 available
 $3.99
Add To Cart
Fig #ImgPart NameAvailabilityPrice
A16
Decal-Warning
Decal-Warning
Part #: 984032001
In stock
3 available
 $0.99
Add To Cart
A17
Upper Boom And Cable Assembly (Fits Models CS 30 And SS 30)
Upper Boom And Cable Assembly (Fits Models CS 30 And SS 30) Obsolete - Not Available
Part #: 000998353
Discontinued
N/A
A18
Compression Spring
Compression Spring Obsolete - Limited Quantity
Part #: 678252001
In stock
2 available
 $3.99
Add To Cart
A19
Front Handle Assembly (CS30 And SS30)
Front Handle Assembly (CS30 And SS30)
Part #: 308472001
In stock
4 available
 $9.61
Add To Cart
A20
Bolt (M5 X 30 mm Hex Hd.) (CS30 And SS30)
Bolt (M5 X 30 mm Hex Hd.) (CS30 And SS30)
Part #: 660881001
Ships in 8 - 14 business days
 $0.99
Add To Cart
A21
Wing Nut (M5)
Wing Nut (M5)
Part #: 678256001
Ships in 8 - 14 business days
 $0.99
Add To Cart
A22
Clamp
Clamp
Part #: 984251001
In stock
1 available
 $4.58
Add To Cart
A23
Hex Nut (BC)
Hex Nut (BC)
Part #: 81242
In stock
4 available
 $2.99
Add To Cart
A24
Washer (BC)
Washer (BC)
Part #: 678013001
In stock
4 available
 $3.99
Add To Cart
A25
Handle Bar Clamp
Handle Bar Clamp
Part #: 099075001007
Note: Quantity of 2 needed for whole clamp
In stock
10 available
 $2.99
Add To Cart
A26
Screw (BC)
Screw (BC)
Part #: 82496
In stock
6 available
 $3.99
Add To Cart
A27
Bolt (1/4-20 X 1-1/2 In. Hex Hd.) (BC30)
Bolt (1/4-20 X 1-1/2 In. Hex Hd.) (BC30)
Part #: 660643001
In stock
6 available
 $0.99
Add To Cart
A28
"J" Handle And Grip (BC)
"J" Handle And Grip (BC)
Part #: A08130
In stock
6 available
 $7.67
Add To Cart
A29
Lock Washer (BC)
Lock Washer (BC)
Part #: 83009
In stock
5 available
 $3.99
Add To Cart
A30
Switch (Momentary Contact)
Switch (Momentary Contact)
Part #: PS02764
In stock
5 available
 $3.99
Add To Cart
Fig #ImgPart NameAvailabilityPrice
A31
Throttle Cable Assembly
Throttle Cable Assembly
Part #: 308439001
In stock
7 available
 $4.86
Add To Cart
A32
Screw (10 - 24 X 7/8)
Screw (10 - 24 X 7/8)
Part #: 660616001
In stock
16 available
 $2.99
Add To Cart
A33
Hanger Cap
Hanger Cap
Part #: 099078001039
In stock
25+ available
 $1.13
Add To Cart
A34
Shoulder Strap (BC)
Shoulder Strap (BC)
Part #: 308487001
In stock
5 available
 $13.45
Add To Cart
A
Operator's Manual Obsolete - Not Available
Part #: 987000116
Discontinued
N/A
Engine Assembly
Click to expand
 Fig # Img Part Name Availability Price
B1
Screw, Truss Hd. - (10-24 X 2.188)
Screw, Truss Hd. - (10-24 X 2.188)
Part #: PS03999
In stock
12 available
 $2.99
Add To Cart
B2
Heat Shield (Cat.)
Heat Shield (Cat.)
Part #: 984743001
In stock
3 available
 $2.61
Add To Cart
B3
Muffler Assembly
Muffler Assembly Obsolete - Not Available
Part #: 985869001
Discontinued
N/A
B4
Muffler Gasket
Muffler Gasket
Part #: 900994006
In stock
5 available
 $3.99
Add To Cart
B5
Short Block Assembly (30 CC) (External Gaskets Not Included)
Short Block Assembly (30 CC) (External Gaskets Not Included)
Part #: 308192004
Ships in 8 - 14 business days
 $48.55
Add To Cart
B6
Intake Gasket
Intake Gasket
Part #: 985248001
In stock
8 available
 $3.99
Add To Cart
B7
Gasket
Gasket
Part #: 900954001
In stock
16 available
 $0.85
Add To Cart
B8
Rear Housing
Rear Housing
Part #: 984829001
In stock
3 available
 $8.22
Add To Cart
B9
Screw (10-14 X .875 In. THD. Form.)
Screw (10-14 X .875 In. THD. Form.)
Part #: 82537
In stock
11 available
 $0.85
Add To Cart
B10
Screw (10-24 X 3/4 In. Pan Hd. Torx)
Screw (10-24 X 3/4 In. Pan Hd. Torx)
Part #: 984812001
In stock
6 available
 $2.27
Add To Cart
B11
Screw (Torx Pan Hd. Sems)
Screw (Torx Pan Hd. Sems)
Part #: 093221
In stock
11 available
 $2.99
Add To Cart
B12
Carburetor Gasket
Carburetor Gasket
Part #: 9074002
In stock
7 available
 $3.99
Add To Cart
B13
Carburetor Gasket
Carburetor Gasket
Part #: 900994004
In stock
25+ available
 $0.85
Add To Cart
B14
Roto-Choke Base
Roto-Choke Base
Part #: 518498002
In stock
2 available
 $3.99
Add To Cart
B15
Nut (M5-0.8 X 5)
Nut (M5-0.8 X 5)
Part #: 678536001
Ships in 8 - 14 business days
 $0.99
Add To Cart
Fig #ImgPart NameAvailabilityPrice
B16
Carburetor Assembly
Carburetor Assembly
Part #: 308054007
In stock
7 available
 $20.70
Add To Cart
B17
Gasket
Gasket
Part #: 5945603
In stock
18 available
 $3.99
Add To Cart
B18
Heat Dam
Heat Dam
Part #: 518070001
In stock
12 available
 $3.99
Add To Cart
B19
Tank Insulation Gasket
Tank Insulation Gasket
Part #: 900999002
In stock
7 available
 $3.99
Add To Cart
B20
Bumper
Bumper
Part #: 570549001
In stock
25+ available
 $3.99
Add To Cart
B21
Fuel Tank Assembly W/Cap
Fuel Tank Assembly W/Cap Obsolete - Not Available
Part #: 308181005
Discontinued
N/A
B22
Bumper
Bumper
Part #: 98792
In stock
25+ available
 $0.85
Add To Cart
B23
Rotor W/Pawls Assembly (Tech Tip: Locktite this part to the shaf
Rotor W/Pawls Assembly (Tech Tip: Locktite this part to the shaf
Part #: 308433001
In stock
8 available
 $17.84
Add To Cart
B24
Washer
Washer
Part #: PS05268
In stock
9 available
 $3.99
Add To Cart
B25
Lead
Lead
Part #: A06963
In stock
3 available
 $1.56
Add To Cart
B26
Lead W/Terminals
Lead W/Terminals
Part #: A06964
In stock
3 available
 $3.99
Add To Cart
B27
Ignition Module W/3 Sec. Kill Switch
Ignition Module W/3 Sec. Kill Switch
Part #: 308389002
In stock
7 available
 $19.95
Add To Cart
B28
Screw (8-32 X 1 In. Torx Pan Hd.)
Screw (8-32 X 1 In. Torx Pan Hd.)
Part #: 82540
Note: Torque Specs: 30-40 In/Lbs; 3.4-4.5 Nm
In stock
3 available
 $0.99
Add To Cart
B29
Spacer Tube
Spacer Tube
Part #: 638091003
In stock
1 available
 $1.74
Add To Cart
B30
Washer
Washer
Part #: 638090001
In stock
5 available
 $0.86
Add To Cart
Fig #ImgPart NameAvailabilityPrice
B31
Clutch Assembly
Clutch Assembly
Part #: 300960002
In stock
9 available
 $8.23
Add To Cart
B32
Clutch Washer (sold individually)
Clutch Washer (sold individually)
Part #: 678257001
In stock
5 available
 $1.13
Add To Cart
B33
Drum And Connector
Drum And Connector
Part #: 308177001
Note: Torque Specs: 40-50 In/Lbs; 4.5-5.6 Nm
In stock
11 available
 $13.27
Add To Cart
B34
Screw (ST-155)
Screw (ST-155)
Part #: 82538
In stock
12 available
 $2.99
Add To Cart
B35
Starter Housing And Eyelet Assembly
Starter Housing And Eyelet Assembly Obsolete - Limited Quantity
Part #: 308436001
In stock
1 available
 $10.92
Add To Cart
B36
Spring & Container
Spring & Container
Part #: 638033001
In stock
25+ available
 $3.99
Add To Cart
B37
Starter Pulley
Starter Pulley
Part #: 308374001
In stock
20 available
 $9.78
Add To Cart
B38
Screw-Thread Form (8-16 X 1/2")
Screw-Thread Form (8-16 X 1/2")
Part #: 82543
Note: Torque Specs: 15-25 In/Lbs; 1.7-2.8 Nm
In stock
7 available
 $2.99
Add To Cart
B39
Baffle/Isolator
Baffle/Isolator
Part #: 638229001
In stock
2 available
 $3.02
Add To Cart
B40
Rope-Starter
Rope-Starter Obsolete - Not Available
Part #: 9789904
Discontinued
N/A
B41
Starter Grip
Starter Grip
Part #: PS06114
In stock
12 available
 $0.85
Add To Cart
B42
Starter Housing Assembly
Starter Housing Assembly Obsolete - Not Available
Part #: 308194004
Note: Includes Figure Nos 35-41
Discontinued
N/A
B43
Bolt (M5-0.8 X 57)
Bolt (M5-0.8 X 57)
Part #: 660454002
In stock
6 available
 $0.99
Add To Cart
B44
Double Sided Hex Bolt
Double Sided Hex Bolt
Part #: 660453002
In stock
2 available
 $0.99
Add To Cart
B45
Piston Ring 30CC
Piston Ring 30CC
Part #: 690161005
In stock
11 available
 $2.99
Add To Cart
Fig #ImgPart NameAvailabilityPrice
B46
Piston W/Pin
Piston W/Pin Obsolete - Not Available
Part #: 985872001
Discontinued
N/A
B47
Cylinder
Cylinder
Part #: 640069003
In stock
3 available
 $36.18
Add To Cart
B48
Cylinder Gasket
Cylinder Gasket
Part #: 900953001
In stock
12 available
 $3.99
Add To Cart
B49
Screw (M5 X 20 mm)
Screw (M5 X 20 mm)
Part #: 660342002
In stock
12 available
 $1.99
Add To Cart
Lower Shaft Assembly
Click to expand
 Fig # Img Part Name Availability Price
C1
Expand-It Label
Expand-It Label
Part #: 985165001
In stock
2 available
 $0.99
Add To Cart
C2
Decal-Warning
Decal-Warning
Part #: 984032001
In stock
3 available
 $0.99
Add To Cart
C3
Curved Shaft Assembly
Curved Shaft Assembly Obsolete - Not Available
Part #: 000998239
Discontinued
N/A
C4
Grass Deflector Assembly
Grass Deflector Assembly
Part #: T308744001
In stock
25+ available
 $2.85
Add To Cart
C5
Fastener Parts Kit
Fastener Parts Kit Obsolete - Not Available
Part #: PA00249
Discontinued
N/A
C6
Spool Retainer (Black-RH Thread)
Spool Retainer (Black-RH Thread)
Part #: 308042002
In stock
25+ available
 $12.26
Add To Cart
C7
Complete String Head (.080 In.)
Complete String Head (.080 In.)
Part #: 000998360
Note: Includes Figure Nos 6, 8, and 9
In stock
4 available
 $13.14
Add To Cart
C8
Spool And String (.080 In.)
Spool And String (.080 In.)
Part #: 308044007
In stock
17 available
 $4.39
Add To Cart
C9
Spring
Spring
Part #: 06713
In stock
25+ available
 $3.99
Add To Cart

Enter your engine's type number in this search field to show the parts that match your engine.

Your engine's type number is the second part of the model number stamped on your Briggs & Stratton engine (see picture).

Trimmer Parts

Repair Guides
Line Trimmers 101
Line Trimmers 101

This article explains the basic types and features of line trimmers, and it also offers purchasing guidelines for line garden trimmers.

How to Remove a Trimmer Clutch

This video explains how to remove the clutch from most line and string trimmers. Tips are provided for removing tricky clutch drum screws.

Lawn and Garden Machines and Power Tools
Lawn and Garden Machines and Power Tools

This article lists the major categories of lawn and garden tools and machines, explaining the basic applications, types, and features of each.

How to Winterize Power Tools and Machines

This video explains how to properly winterize power tools and machines for winter storage, increasing the life and performance of seasonal tools.

Discussion
Discussion for the Ryobi RY30524 String Trimmer

Post a Comment
Login or signup to comment.
Login or signup to comment.
Ask a question, answer a question, or post a comment!
  • Subject:
  •  
  • Comment:
  •  
how does this come off?
WJA
Reply: Clutch Assembly Part#300960002 R...

WJA

Hello 1124812,

We have prepared two articles and videos to help you with your project. The first one will show how to get to your clutch, and you will notice that the clutch show on the first video does not look like the one on your trimmer. The second video shows how to remove the clutch off of a chainsaw with a clutch like yours.

How to Remove a Trimmer Clutch

How to Replace the Sprocket on a Chainsaw

Your clutch should be a standard RH thread.

I hope these will help you with your repair,
-WJA
sydwyndr
Question: Carb Primer Assembly

sydwyndr

does anybody know if there is a part number or availability of the rubber check valve inside/ under the the primer bulb at the top of the carb?
ShotOut
Reply: Carb Primer Assembly

ShotOut

The little marroon or orange check valves made by Walbro will fit these carbs. They have them on Ebay. Search under Walbro Check Valve. They fit and they work.
joe bruno
Question: Weed Wacker

joe bruno

how do you remove the drum and clutch assembly on weed wacker model # ry30524 / 30cc and what tools do you need?
ShotOut
Reply: Weed Wacker

ShotOut

Remove the tube that holds the flex-drive shaft from the front of the motor cover.Remove the rear engine cover. Remove the throttle cable from the carburetor. Mark and unplug any wires for the on/off switch that go to the ignition coil (underneath front cover) if possible. Now if you have pulled the driveshaft tube out of the way, the clutch drum is up next. Inside it, screwed into the very end of the engine's crankshaft is a Torx #25 screw. Before you loosen it, you will have to lock up the engine. To do so, remove the spark plug. Pull on the starter until the piston is down, then insert a length of clean, soft rope into the engine. The engine will come up and compress the rope, thus locking it in place to allow clutch drum and clutch removal. Loosen the T-25 (Star bit or Torx head) screw inside the drum.. You may be able to remove it with a long thin-blade screwdriver also.It probably won't come completely out...it is made this way. Next, remove the clutch. It is screwed onto a small threaded section of the crankshaft Removal is counterclockwise.. It will be pretty tight. To help, apply peneterating oil. Whack the ears of the clutch near the center with a hammer and a dull flat-blade chisel or a small piece of wood unless there are bolts. then use a wrench. It will turn counterclockwise for removal and there will probably be a removal direction arrow on it's face. After getting that off, remove the Torx screws holding the cover to the engine. The starter unit should be mounted inside as it mates with the top of the flywheel to start the motor. Remember to preload tension (5-7 turns) on the starter unit. Make sure the handle is installed. Jam the unit with a screwdriver or vise grips so you can insert and tie off the new rope. Then remove jam device and let recoil pull your new rope into place while holding the handle. Reassemble and you are done. Disassembly requires Torx head drivers and a good flat-blade screwdriver. Post back if needed
UtahAV
Reply: Weed Wacker

UtahAV

Hi Joe,

Removal of the clutch drum isn't too hard of a project at all if you know a few tricks first. We have prepared an article and video that will provide you with all of the information you will need to remove the clutch drum. You can find the article and video at the following link...

How to Remove a Trimmer Clutch : eReplacementParts.com

I hope this helps you with your repair!

-Mark
Jim
Question: Ry 30524 Gas Problem

Jim

My weed wacker would not run for more than 30 sec at a time. I took it apart (carefully) cleaned it but found no indication of clogging. When I try to start it now it spits gas out the exhaust but will not start. Help.
ShotOut
Reply: Ry 30524 Gas Problem

ShotOut

The carburetor probably needs to be adjusted (H and L mixture screws) or have some new parts installed. The RUIING carbs on these don't have rebuild kits but they have parts that mimic Walbro diaphragm carbs and are probably compatible.
ray mcnally
Question: Throttle / High Speed Problem

ray mcnally

The engine starts and idles OK but when throttle is applied the engine quickly dies. Why?
jw smith
Reply: Throttle / High Speed Problem

jw smith

The engine starts and idles OK but when throttle is applied the engine quickly dies. Why?
UtahAV
Reply: Throttle / High Speed Problem

UtahAV

That sounds like dirt or debris in the carburetor. When an engine is first started and is idling it is pulling fuel through what is called the idle circuit in the carburetor. The idle circuit is just a passage in the carb that works when less air is being drawn into the carb. When you throttle the engine up the fuel now flows through the main jet in the carb. My guess it that your main jet is clogged. That is why it will run at idle but die when throttle is applied. A good carburetor cleaning should solve the problem.

I hope this helps,

-UtahAV
-Mark
ShotOut
Reply: Throttle / High Speed Problem

ShotOut

The L mixture screw in the carb needs adjusting. Get an automotive type wire connector (say 22 gauge) and tap the end of it over the head of the L mixture screw (screw closest to the engine). With it running, turn it counterclockwise about 1/8 to 1/4 of a turn to improve acceleration.
ShotOut
Reply: Throttle / High Speed Problem

ShotOut

The L mixture screw needs adjusting. Get an automotive type wire connector (22 gauge) and tap the plastic end of it over the head of the L mixture screw (screw closest to the engine). Then get it running and while attempting to throttle up, turn that screw 1/8 to 1/4 of a turn clounterclockwise.
I went to empty out the gas in my machine(stated above) and discovered that the hose connected to the fuel filter, that is inside the gas tank enclosure, was deteriorated and in many pieces.

My questions are:
Does the Gas Tank Enclosure you sell include the hoses and fuel filter?
What might have caused the hoses to deteriorate like that?

Any help would be greatly appreciated!
Sam
Reply: Cs30 Ry30524 Fuel Filter Gas Tan...

Sam

Mine did the same thing. Both rubber hoses were deteriorated. What caused this and will a new tank assembly contain the hoses and fuel filter?
ShotOut
Reply: Cs30 Ry30524 Fuel Filter Gas Tan...

ShotOut

Go to the garden center at Home Depot. They have a Ryobi fuel kit for about 7 clams. It has the fuel lines and filter you need to fix your machine...and I think it includes the primer bulb too!
ShotOut
Reply: Cs30 Ry30524 Fuel Filter Gas Tan...

ShotOut

Age and ethanol in the gas cause deterioration of fuel lines. Replace with the Ryobi fuel line kit from Home Depot.
ShotOut
Reply: Cs30 Ry30524 Fuel Filter Gas Tan...

ShotOut

I don't work here. Go to Home Depot garden center and get the $7 fuel line kit. It works.l
carlson
Question: Weed Wacker

carlson

When I start my machine it runs good in idle. As soon as I press the gas it shuts off. What causes this and what can I do to fix it?
ShotOut
Reply: Weed Wacker

ShotOut

Adjust the L mixture screw on the Ruiing carb out 1/8 to 1/4 a turn counterclockwise until it throttles up.
Is there a special tool or procedure to remove the connector / drum assembly? (I am replacing the ignition module.)
ShotOut
Reply: Removal Of Connector & Drum (B-3...

ShotOut

The drum assembly is actually the housing for the clutch. Here are instructions for removing it.
Remove the tube that holds the flex-drive shaft from the front of the motor cover.Remove the rear engine cover. Remove the throttle cable from the carburetor. Mark and unplug any wires for the on/off switch that go to the ignition coil (underneath front cover) if possible. Now if you have pulled the driveshaft tube out of the way, the clutch drum is up next. Inside it, screwed into the very end of the engine's crankshaft is a Torx #25 screw. Before you loosen it, you will have to lock up the engine. To do so, remove the spark plug. Pull on the starter until the piston is down, then insert a length of clean, soft rope into the engine. The engine will come up and compress the rope, thus locking it in place to allow clutch drum and clutch removal. Loosen the T-25 (Star bit or Torx head) screw inside the drum.. You may be able to remove it with a long thin-blade screwdriver also.It probably won't come completely out...it is made this way. Next, remove the clutch. It is screwed onto a small threaded section of the crankshaft Removal is counterclockwise.. It will be pretty tight. To help, apply peneterating oil. Whack the ears of the clutch near the center with a hammer and a dull flat-blade chisel or a small piece of wood unless there are bolts. then use a wrench. It will turn counterclockwise for removal and there will probably be a removal direction arrow on it's face. After getting that off, remove the Torx screws holding the cover to the engine. The starter unit should be mounted inside as it mates with the top of the flywheel to start the motor. Remember to preload tension (5-7 turns) on the starter unit. Make sure the handle is installed. Jam the unit with a screwdriver or vise grips so you can insert and tie off the new rope. Then remove jam device and let recoil pull your new rope into place while holding the handle. Reassemble and you are done. Disassembly requires Torx head drivers and a good flat-blade screwdriver. Post back if needed
UtahAV
Reply: Removal Of Connector & Drum (B-3...

UtahAV

Hi Kelly,

Removal of the clutch drum isn't too hard of a project at all if you know a few tricks first. We have prepared an article and video that will provide you with all of the information you will need to remove the clutch drum. You can find the article and video at the following link...

How to Remove a Trimmer Clutch : eReplacementParts.com

I hope this helps you with your repair!

-Mark
Dewey
Question: Diaphram

Dewey

Can I purchase the carburetor diaphragm and replace it?
Mark
Reply: Diaphram

Mark

Hi Dewey,

Unfortunately there are no separate parts available for the carburetor. The carburetor is only available as a complete assembly. It is part #308054007 and is available from http://www.ereplacementparts.com.

Good luck with your repair!

-Mark

ShotOut
Reply: Diaphram

ShotOut

If you have some skills at cross referencing parts you can. This is a RUIING carburetor that is a Chinese knockoff of a Walbro. The standard Walbro gasket and diaphragm kit will probably be compatible. They don't sell individual parts for these carburetors.
When you replace the complete head on the sc30 string trimmer does it contain the washer that holds it on?
Mark
Reply: When Youpuy On A New Hesd Comple...

Mark

Hi Jim,

Yes, the trimmer head assembly includes the housing, the spool, the spring and the spool retaining knob.

The trimmer head assembly is part #000998360 and is available from http://ereplacementparts.com.

Good luck with your repair!

-Mark
Pat
Question: Primer Bulb

Pat

My question is the same as Dotty's -
How can you get a primer bulb for RY 30524 (CS30) ?
Mark
Reply: Primer Bulb

Mark

Hi Pat,

The primer bulb for your trimmer is built into the carburetor. Ryobi doesn't manufacture the carb themselves but purchases it from a 3rd party. Because of this Ryobi does not offer any parts for the carburetor. To replace the primer bulb you will need to replace the carburetor. The carburetor is part #308054007 and is available from http://ereplacementparts.com.

I hope this helps with your repair!

-Mark
ShotOut
Reply: Primer Bulb

ShotOut

In the fuel line kit available in the Garden Center at Home Depot.
Dotty
Question: Primer Bulb

Dotty

How do you get a primer bulb replacement for a RY30524 Ryobi trimmer. Thank You for your help.
Mark
Reply: Primer Bulb

Mark

Hi Dotty,

Ryobi does not offer the primer bulb separately from the carburetor. It is only available as a complete assembly. The part number for the carburetor is 308054007 and it is available from http://www.ereplacementparts.com.

Good luck with your repair!

-Mark

Ken
Reply: Primer Bulb

Ken

As of October 2010, Home Depot is now stocking (and hopefully soon EREPLACEMENTPARTS.COM as well) a Ryobi Fuel System Tune-up kit which contains both gas lines, a tool to install them, and the primer bulb.

Part Number is - Ac04101 852-510
UPC Code is - 0-46396-55192-4

Distributed by - Techtronic Industries North America, Inc.
1428 Pearman Dairy Rd.
Anderson, SC 29625



After draining gas tank, it took me less than 5 minutes to install all the components of the kit on my CS30 RY30524. tools required were phillips head screwdriver, torx screwdriver, small brush, and small wrench or socket driver, pliers.

Gas lines - drain gas tank, remove gas tank cap, carefully pull with fingers, or cut with knife or use pliers
the gas lines off the carb. Do the replacement one line at a time to avoid confusion.
Pull return line out of gas tank carefully from the outside. The inline also has a fuel filter on it. Push the line into the tank and tilt trimmer so line and filter drop out of gas tank filler spout. Follow instruction sheet in Kit to install new lines.

Primer bulb replacement - turn choke dial to full choke position,
use pliers, socket driver or small wrench and remove hex nut from Choke dial cover, remove wavy washer and flat washer and dial cover

use brush to clean debris from air filter screen.
use torx (T15?) screwdriver to remove torx screw just behind the filter screen assembly. Not sure what the whole assembly is called, but it contains the choke run dial and filter screen. removing the screw will allow you to gently rotate the assembly counter clockwise slightly to expose the second plate screw for the primer bulb.
use the phillips screwdriver to remove the two retaining screws
for the primer bulb retention plate. remove plate and replace primer bulb with new one., replace the two phillips screws, rotate the assembly clockwise so that screw hole lines up again,
replace torx screw for the assembly.

install choke dial back on shaft with arrow pointed at full choke and reinstall washers and hex nut.
ShotOut
Reply: Primer Bulb

ShotOut

Home Depot Garden Center.
ShotOut
Reply: Primer Bulb

ShotOut

There is a new one in the fuel line kit available in the garden center at Home Depot. See details in post below.
Accessories
Accessories for the RY30524

Mix Oils:
See more mix oils 
6450025
Power Blend Ultimate 2-Stroke Oil 6.4 oz.
$3.99

T-00745
2-Stroke Oil w/ Stabilizer 50:1 Ratio 2.6 fl.oz
$3.99

80036
Shindaiwa One Engine Oil
$2.99

fancyboxy