Rubber Sleeve 29 422032-1
Part Number: 422032-1
Order within the next 12 hours
and your part ships today!
and your part ships today!
Product Information
Specifications
|
Description:
| This rubber sleeve, also known as a rubber dam, is sourced from the original manufacturer for use with sanders. It has a length of 3 inches, an outer diameter of 3/8 inches, and an inner diameter of 1-1/8. The sleeve allows the sander belt to spin smoothly by providing it with the necessary grip. It is normal for the rubber sleeve to tear, lose elasticity, or fall off due to aging and frequent use. A faulty sleeve will result in belt slippage, increased noise, overheating, and equipment instability. Remove the equipment housing to access the driving roller. Remove the fasteners that hold the driving roller and pull the roller out. Slide the faulty rubber sleeve off and clean the roller to ensure a good seal for the new sleeve. Place the new sleeve on the roller and return the roller to the equipment. Reinstall the fasteners and reassemble the equipment housing. |
Frequently Purchased With
Compatibility
This part is compatible with the following machines:
Products Compatibility
This item works with the following types of products:
- • Sander
Questions & Answers for Rubber Sleeve 29
No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
3 of 3 people found this instruction helpful
Tool Type:
Sander
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, liquid soap
The rubber sleeve started to break off due to old age
1. Remove cover to access the drive roller
2. Remove the drive roller
3. Remove old rubber cover and any dirt/debris
4. Rub some liquid soap on the roller
5. Slide the new rubber cover onto the drive roller
6. Re install the drive roller and the access cover
2. Remove the drive roller
3. Remove old rubber cover and any dirt/debris
4. Rub some liquid soap on the roller
5. Slide the new rubber cover onto the drive roller
6. Re install the drive roller and the access cover
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Sander
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers, snapring pliers.liquid soap to slide sleeve on
Belt sander rollers were torn and walked the belt off the end
Relatively easy, had to remove 3 screws and slide the unit out. the snap ring pliers were used to allow the shaft to slide out to replace the drive roller out to be replaced, reassembled and it worked perfectly.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 4 people found this instruction helpful
Tool Type:
Sander
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers, Snap ring pliers
Sanding belt was slipping
Remove the snap ring from the shaft in the front roller.
Remove the shaft and roller.
Place the new front roller in the roller arm, then insert the shaft into the roller arm and front roller and attach the snap ring.
Remove the old rubber sleeve from the rear roller and then press the new sleeve on the roller.
Remove the shaft and roller.
Place the new front roller in the roller arm, then insert the shaft into the roller arm and front roller and attach the snap ring.
Remove the old rubber sleeve from the rear roller and then press the new sleeve on the roller.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Sander
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers
brushes worn
Carbon brushes had worn out. I have had this Makita for 15 years. I was easy to install by taking the screws on one side out, take the two screws for the brushes out and install the new ones.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
2 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
2
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
easy
worked great easy to order theonly bad thing was it cost more to aship then part price
Guest -
June 1, 2023
Verified Purchase
Easy to identify, order and receive the correct part
I needed a rubber rolling sleeve for a belt sander that is no longer manufactured. It was easy to find the correct part with the exploded parts view and table of parts. The order was processed quickly and the part fit perfectly.
Guest -
July 29, 2019
Verified Purchase
Verified Purchase
eReplacementParts Team
< PREV
- 1
Product Information
