Repair Parts Home    Lawn Equipment Parts    Homelite Parts    3290875G Retaining Ring

3290875G Retaining Ring

Part Number: 3290875G
HomeliteRyobi
Availability: 25+ in stock
Price: $2.99
Quantity:
Order within the next 9 hours
and your part ships today!
Description:
This is a genuine OEM replacement part, it is sold individually.
The purpose of the 3290875G Retaining Ring is to attach and hold the washer and sprocket to the driveshaft on the models shown below.

To remove this part it is best to use retaining ring pliers (or snap ring pliers).

Repair Stories
0 of 0 people found this instruction helpful
Tool Type:
Pole Saw
Parts Used:
Chain Adjustment Assembly - 31307152G
Washer - 33302102G
Oil Filler Cap - 34117152-3G
Retaining Ring - 3290875G
Sprocket - 33902102-1G
Repair Difficulty:
Easy
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, Wrench Set, Retaining clip replacement tool
Chain came off during use, doing a bit of damage to the plastic parts, causing the retaining clip and washer to fly off and dissapear in the vacant lot.
Dissembled pole saw using a phone camera to document where parts came from to ensure they were replaced properly. Ordering and waiting for new parts, exceeds my short term memory time span. Individual parts were not too expensive so I ordered several new parts that may not have been necessary but my logic was to extend the life of the pole saw. Parts came and I cleaned all existing part of saw from debris and chain saw oil. Replaced parts (used photos - learned this a long time ago, the hard way). The only guess was which side of the sprocket the washer belonged on as the original was blown away. The new sprocket was just a bit too thick so the retaining clip would not go on. The old sprocket looked fine so I reused it. Using the retaining clip tool, well worth a $6-7 price, I reassembled the saw. Works like it is supposed to and now I have a large pile of tree branches to haul away. I have not yet replaced the switch parts but will. The current switch requires me to press and pull in just the necessary angle to engage the motor. I ordered those parts at the same time. Great source of parts; timely shipping; trouble free. Will use ereplacementparts again.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
0 of 0 people found this instruction helpful
Tool Type:
Pole Saw
Parts Used:
Washer - 33302102G
Retaining Ring - 3290875G
Hex Nut - 32901152G
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Socket set, retaining ring pliers
Lost hex nut while replacing chain also retaining ring came off and needed to be replaced
Put washer on sprocket and used small pair of retaining ring pliers to spread ring to secure the washer. Replaced chain and reassembled using the new hex nut. Spent more time locating retaining ring pliers than it took to do the whole repair.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 2 people found this instruction helpful
Tool Type:
Chain Saw
Parts Used:
Washer - 33302102G
Retaining Ring - 3290875G
Sprocket - 33902102-1G
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
, tack hammer
The retaining ring and washer slipped off the spline and were lost and needed to be replaced
Remove the chain cover, loosen the chain. Remove chain and bar. Use retaining ring pliers to remove the retaining ring from slot in the shaft, then the washer then slide off the old sprocket. Install the new parts in reverse order. Now it is installed, the chain cannot slide off the sprocket, and the saw works perfectly once again.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
0 of 1 people found this instruction helpful
Tool Type:
Pole Saw
Parts Used:
Washer - 33302102G
Chain - 901289001
Retaining Ring - 3290875G
Repair Difficulty:
Medium
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Pliers
retaining ring fell off
I removed the chain cover, then I used a retaining ring pliers to remove the ring. Replaced the retaining ring and washer. Replaced the dull chain onto the sprocket and on the bar. Replaced the chain cover and then tensioned the chain to the proper tension.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Discussion
Discussion for Retaining Ring - ( 3290875G )
You need to be signed in to participate in the discussion.
You need to be signed in to particupate in the discussion.
Ask a question, answer a question, or post a comment!
  • Subject:
  •  
  • Comment:
  •  
1174347
Question: Retaining Ring

1174347

looking for the size of the retaining ring to have some spairs
WJA
Reply: Retaining Ring

WJA

Hello 1174347,

The OD of the part number 3290875G retaining ring is 1/2 inch.

Hope this helps,
-WJA
Product Information
Manufacturer: Homelite, Ryobi
Category Number: 3290875G
Classification: Part
Weight: 0.01 lbs.
Shipping: Ships Worldwide world wide shipping icon
Repair Guides
Articles:
How to Replace the Fuel Filters in Your Outdoor Power Equipment
This article will help you troubleshoot your fuel-line replacement repairs. ...
November 15, 2012
Quick Fix: How to Replace the Spark Plug in a Small Engine
This article will help you replace the spark plug on a small engine which will help get your gas powered equipment up an...
November 15, 2012
fancyboxy