This is a genuine manufacturer-sourced part which is made for Ryobi and Homelite electric log splitters. It is an identical replacement for a missing or a damaged ram valve assembly. The part is an important component that creates pressure inside the cylinder. Refer to the appropriate diagrams for your model to ensure the correct repair procedure. The assembly conconsists of one durable metal ram valve, one seal and a spring. A screwdriver and a wrench set might be needed to replace these parts.
Ram Valve Assembly 099077001503
OEM part for: Ryobi, Homelite
Part Number: 099077001503
Compatibility
This part will fit the following 2 machines
Ryobi
Homelite
This item works with the following types of products:
- Log Splitter Parts
Customer Part Reviews ?
- 1
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Ram Valve Assembly
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Ram valve was broken
Tool Type
Log Splitter
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver, Wrench Set
Parts Used
Then loosen cylinder bolt on opposite side.
Remove handle over ram valve (back end two bolts)
Then slowly pull ram valve out. ( hint put splitter in wheelbarrow to catch oil)
Push new ram valve in place.
Then tighten cylinder bolt reassemble handle and you should be good to go!
Low power stroke
Tool Type
Log Splitter
Difficulty
Medium
Time
15-30 minutes
Tools Used
Adjustable Wrench, hammer
Parts Used
2. Removed valve assembly, needed brass sleeve to take out old Valve sleeve, had broken spring and seals were torn.
3. Installed new Assembly.
4. Tested works fine.
Valve went bad
Tool Type
Log Splitter
Difficulty
Easy
Time
15-30 minutes
Tools Used
Wrench Set
Install the new valve, then the bolt.
piston would not retract as valve was stuck open
Tool Type
Log Splitter
Difficulty
Medium
Time
30-60 minutes
Tools Used
Screwdriver, Socket set, hammer
Parts Used
Replaced with new valve and drove it back in place with a small bolt head and hammer.
Put handle back on, now difficult because of pressure from new valve.
Tested splitter. Now functioning properly
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.