Medium
15-30 minutes
The power switch connects to the brushroll sensor screw. It is an authentic OEM sourced item which is specially produced for use with Kirby vacuums. This item is sold individually. A screwdriver might be necessary during the installation of this part. It will require replacing if it becomes broken.
Power Switch G3-sentria K-110590
OEM part for: Kirby
Part Number: K-110590
$69.47
Usually ships in 7 - 12 business days
Leaves our warehouse within 7 - 12 business days
Compatibility
This part will fit the following 7 machines
Kirby
G3 Vacuum View Diagrams & Manuals
G4 Vacuum View Diagrams & Manuals
G5 Vacuum View Diagrams & Manuals
G6 Vacuum View Diagrams & Manuals
Ultimate G Vacuum View Diagrams & Manuals
Diamond Edition Vacuum View Diagrams & Manuals
Sentria Vacuum View Diagrams & Manuals
Show More Compatible Models
This item works with the following types of products:
- Vacuum Parts
Customer Part Reviews ?
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Power Switch G3-sentria
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
On off switch was not working
Dave - January 25, 2018
👍 7 of 10 people found this instruction helpful
Tool Type
Vacuum
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver, Torx bits
Parts Used
Started with removing front brush head, then remove cover from switch cover with screw driver in small hole to pop off. Remove torx screw that holds power cord on and the screw on side there the power cord is. Then two screws on each side to take top cover off. There are four screws in front, two on each side and the two screws on back of the top of power head. Remove wires to switch make sure you mark them to remember were they go. Remove screw on switch. Need to remove rod from switch, push switch back to unlock it from pins. Then need to wiggly it out, you will need to push in the safety switch that goes throw the front of machine as you try to pull it out. Then replace switch with new one, and repeat this back words to complete job. I hope I listed it all. thank you
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
