O-ring 884585
Part Number: 884585
Order within the next 6 hours
and your part ships today!
and your part ships today!
Product Information
Description:
This is an authentic manufacturer sourced replacement part that is specially produced for Porter Cable nailers and staplers. It helps to provide an air tight seal between the piston and the cylinder walls. This o-ring is made from durable rubber material and it is sold individually. To complete this repair you will need a hex key also known as an allen wrench. |
Frequently Purchased With
Products Compatibility
This item works with the following types of products:
- • Nailer
- • Stapler
Questions & Answers for O-ring
No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
Tool Type:
Nailer
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Wrench Set, Mallot
Leaking air, would not shoot
Replaced the "O" ring. Put it back together, tested it and it worked as if new.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Nailer
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Socket set, Wrench Set, Dental Pick
Nailer won't fire, only leaked air while the trigger was depressed in the trigger area
Disassembled the trigger and then removed the trigger valve from the body of the gun using a socket. I replaced all of the O-rings in the trigger area and lubricated them with the oil that comes with the gun. I then reassembled the valve and screwed it back into the gun body. I reassembled the trigger making sure that the safety worked as it is designed to. The gun worked properly after the repair and continues to at this point. I am satisfied that the O-rings were the cause of the problem.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Nailer
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
, Allen wrench
Leaking air at the top of the nailer.
1. Removed the top of the nailer.
2. Removed the broken piston stop.
3. Put in all new o-rings.
4. Reassembled the nailer.
2. Removed the broken piston stop.
3. Put in all new o-rings.
4. Reassembled the nailer.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Nailer
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Allen wrench
O-rings were bad
Removed the four screws from the cylinder head and removed it
Removed and replaced the worn o-rings
Cleaned and oiled the inside of the gun
Installed the cylinder head
Removed and replaced the worn o-rings
Cleaned and oiled the inside of the gun
Installed the cylinder head
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
4 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
3
4 stars
1
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
o- ring
part was just as ordered and fit perfectly.
Guest -
October 30, 2021
Verified Purchase
nail gun repair
worked as expected
Guest -
May 12, 2020
Verified Purchase
Accurate part replacement
The replacement parts arrived in a reasonable time and fit into my nail gun as expected. My nail gun is now working like it did when it was new. This was a significant savings over buying a new nail gun.
Guest -
November 26, 2019
Verified Purchase
ordered many parts
arrived as described, however, I still can't get my nail gun to fire right after replacing almost all o rings. bought another and will take this one to the auction
Guest -
February 24, 2020
Verified Purchase
Verified Purchase
eReplacementParts Team
< PREV
- 1
Product Information