Easy
15-30 minutes
Genuine manufacturer approved replacement magnetic switch that is specially made for Jet saws. It is the part of the tool handling on/off operations. Over time switch components may wear out eventually requiring replacement. This high quality switch has a plastic body and it is sold individually.
Magnetic Switch 230v 1ph JTAS10-23
OEM part for: Jet
Part Number: JTAS10-23
$242.29
In Stock
Order within the next 12 hours and your part ships today! 
Compatibility
This part will fit the following 5 machines
Jet
XACTA (708674) Deluxe Saw View Diagrams & Manuals
XACTA Deluxe Saw View Diagrams & Manuals
JTAS-10 Tilting Arbor Tablesaw View Diagrams & Manuals
JTAS-10XL Left Tilting Arbor Saw View Diagrams & Manuals
JWP-15CS (708538) 15 in. Thickness Planer View Diagrams & Manuals
This item works with the following types of products:
- Saw Parts
- Table Saw Parts
- Planer Parts
This part replaces obsolete part #: JWBS20-14
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Magnetic Switch 230v 1ph
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Motor stopped working. Plug connection and circuit breaker OK. After removing switch cover, could start motor by manually depressing switch mechanism but switch would not stay engaged.
James - August 11, 2018
👍 2 of 2 people found this instruction helpful
Tool Type
Table Saw
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Pliers, Adjustable Wrench, paper and pencil to document wiring connedtions
Parts Used
1. Unplugged saw.
2. Removed old switch cover with screwdriver.
3. Made a drawing of the wires and terminal connections in switch box.
4. Pulled wires off terminals with needle-nosed pliers.
5. Unscrewed old switch box from machine.
6. Unscrewed plastic devices surrounding the ports where the wires entered and left the switch box.
7. Pulled the old switch box free from the wires.
8. Installed new switch following steps 1-7 in reverse order. Note that the some terminals were in locations different from old switch.
2. Removed old switch cover with screwdriver.
3. Made a drawing of the wires and terminal connections in switch box.
4. Pulled wires off terminals with needle-nosed pliers.
5. Unscrewed old switch box from machine.
6. Unscrewed plastic devices surrounding the ports where the wires entered and left the switch box.
7. Pulled the old switch box free from the wires.
8. Installed new switch following steps 1-7 in reverse order. Note that the some terminals were in locations different from old switch.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Switch went out on my Delta Unisaw
John - July 15, 2017
👍 2 of 2 people found this instruction helpful
Tool Type
Table Saw
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver, Pliers
Parts Used
Uninstalled the old switch and replaced with the new switch.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Delta unisaw with a bum magnetic switch.
Jacques - February 22, 2017
👍 1 of 1 people found this instruction helpful
Tool Type
Table Saw
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
Parts Used
Removed the old switch, then the wires
Installed the new switch and connected the wires to it
Installed the new switch and connected the wires to it
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Start stop controls quit working
Brian - July 13, 2018
Tool Type
Table Saw
Difficulty
Easy
Time
30-60 minutes
Tools Used
Screwdriver
Parts Used
Disconnected power to table saw.
Removed old controls.
Installed new controls.
Energized saw.
Depressed start switch.
Voila...
Removed old controls.
Installed new controls.
Energized saw.
Depressed start switch.
Voila...
Did you find this story helpful?
Thanks for voting and helping fellow customers!
It would not start
Allen - August 18, 2017
Tool Type
Table Saw
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver, Pliers, Adjustable Wrench
Parts Used
Unplugged the machine
Took the cover off
Removed the brace from the bottom of the switch
Removed the wires, one at a time and made note of each position
Unsnapped the grommets holding the wires and removed the switch box
Reinstalled the new switch box in reverse order
Attached wires in the correct places
Replaced cover
Plugged saw up and started it
Took the cover off
Removed the brace from the bottom of the switch
Removed the wires, one at a time and made note of each position
Unsnapped the grommets holding the wires and removed the switch box
Reinstalled the new switch box in reverse order
Attached wires in the correct places
Replaced cover
Plugged saw up and started it
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Switch not working
Thomas - January 24, 2017
Tool Type
Table Saw
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Pliers
Parts Used
Remove the front cover of the switch, and make a wiring diagram.
Disconnect the wires from the switch
Remove the back of the switch, pull wires through
Attach the the back of the new switch and pull the wires through
Connect the wires to the switch
Install the front cover
Disconnect the wires from the switch
Remove the back of the switch, pull wires through
Attach the the back of the new switch and pull the wires through
Connect the wires to the switch
Install the front cover
Did you find this story helpful?
Thanks for voting and helping fellow customers!
The table saw would start all by itself. Any time, Very dangerous
Darryl - March 5, 2016
👍 1 of 2 people found this instruction helpful
Tool Type
Table Saw
Difficulty
Medium
Time
15-30 minutes
Tools Used
Screwdriver, Pliers
Parts Used
Remove front cover front switch and either take a picture or make a wiring diagram. Disconnect wires from old switch and remove switch from saw. Mount the back of the new switch to the saw, and run the wires thru it. Connect them like the wiring diagram, then place the front of the switch on.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
