Repair Parts Home Lawn Equipment Parts Karcher Parts Karcher Pressure Washer Parts
Karcher G 3050 OH (11945150) Pressure Washer Parts
How to Winterize a Pressure Washer
Learn how to properly winterize your pressure washer by adding antifreeze to the pump, draining the oil, and adding oil to the piston. Read the full article for a step-by-step guide.
How to Test a Small Engine for Spark
If your small engine isn't starting, you'll need to diagnose many issues including the spark plug. This video walks you through the steps of how to test for a spark using a spark tester.
Quick Fix: How to Replace the Outlet Connector on a Karcher Electric Pressure Washer
Learn how simple it is to replace the outlet connector on your Karcher electric pressure washer by reading this repair article.
A Quick Fix: How to Replace the Pump on a Pressure Washer
This article outlines the steps to replace or service the pump on your pressure washer. Doing this repair yourself will save you money and time.
Discussion for the Karcher G 3050 OH (11945150) Pressure Washer
Post a Comment
Ask a question, answer a question, or post a comment!
Question: G3050oh Unloaded Valve
I have Karcher G30500H pressure washer and I suspect it has a defective unloader valve. However, when I removed the old unloader valve it does not look like the one pictured in your parts catalog. Is there a bottom part below the spring that I may have left in the pump? If so, is there a special tool to remove this? The pump does not look like the pump featured in the video on how to replace and unloader now.
Question: HONDA Karcher G3050OH Points Ass...
will not start, minimal spark, new plug, still little spark.
Removed starter cord assembly and cleaned/sanded Magneto and flywheel.
Much better spark but will not fire. Appears to be getting fuel. It only backfires, even with the no no of adding starter fluid.
Question: Karacher G3050OH
Has ANYONE figured out this issue? Mine has been this way since I purchased it and what an annoying feature trying to get work done.
"My pressure goes from high to zero but there is still pressure in the line to the wand even when I shut off the washer. I keep squeezing & releasing the trigger or just holding it open until it decides to come on again and eventually the pressure comes out through the gun. Is it still the spill valve? The gun seems to be the cause. I bought a new gun and that doesn't work on the issue! Suggestions/opinions appreciated." link removed 09/29/2012
Reply: Karacher G3050OH
I took i tin to a repair shop and they couldn't find anything wrong with it....send replkies to user name for hotmail
Reply: Karacher G3050OH
replies to my user name with hotmail for the address. I won' tbe back online for a long time
Question: G 3050 OH Wand Pressure
My pressure goes from high to zero but there is still pressure in the line to the wand even when I shut off the washer. I keep squeezing & releasing the trigger and eventually the pressure comes out through the gun. Is it still the spill valve? The gun seems to be the cause. (I took out the spill/unloader valve, cleaned it, used plumber grease, put it back, still does the same). I am to the point of ordering both parts & hope one fixes it. Suggestions/opinions appreciated.
Reply: G 3050 OH Wand Pressure
Did you ever figure out what was wrong with your G 3050-OH? I have the same model and the same issue. Has acted that way almost since I first started using it. I haven't tried to clean the unloader valve yet, but just curious to see what fixed your prblem.
Question: High Low Pressure
My G 3050 started to stop having a steady pressure flow. It fluctuates from high pressure to no pressure. I have read from other posting, it could be the Unloader but I can not locate it on this model.
Can somebody help?
Reply: High Low Pressure
See diagram B. Parts 1, 2 and 3. Remove them, clean well and coat with plumbers grease.
Should solve the problem.
Question: Engine Won
Since I got it early last year, I hardly used my Karcher 3000 model G3050 OH. All of a sudden, it just won't start. I checked the air filter and saw some traces of oil. I am thinking of cleaning up the cylinder head, but I would need a new head gasket to put it back on.Am I doing the right approach or is there a better way of making it run?
Please help me.