Product Information
Description:
This is an authentic Echo replacement part. The intake gasket is commonly found in backpack blowers. This part is made of high-quality plastic, and is used to seal the connection between the insulator assembly and cylinder. Please be aware that there are different gaskets used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You may require an Allen wrench or screwdriver when replacing this part. This item is sold individually. |
Frequently Purchased With
Compatibility
the 18 compatible machines
This part is compatible with the following machines:
Echo
PB-500H (P01913001001-P01913999999) Backpack Blower
PB-500H (P02112001001-P02112999999) Backpack Blower
PB-500H (P02112001001-P02112999999) Backpack Blower
PB-500T (P01813001001-P01813999999) Backpack Blower
PB-500T (P02212001001-P02212999999) Backpack Blower
PB-500T P31212001001-P31212999999 50.8cc Backpack Power Blower
PB-500T P02011001001-P02011999999 50.8cc Gas Backpack Power Blower
PB-500T P31413001001-P31413999999 50.8cc Backpack Power Blower
PB-500H (P02112001001-P02112999999) Backpack Blower
PB-500H (P02112001001-P02112999999) Backpack Blower
PB-500T (P01813001001-P01813999999) Backpack Blower
PB-500T (P02212001001-P02212999999) Backpack Blower
PB-500T P31212001001-P31212999999 50.8cc Backpack Power Blower
PB-500T P02011001001-P02011999999 50.8cc Gas Backpack Power Blower
PB-500T P31413001001-P31413999999 50.8cc Backpack Power Blower
PB-500T P32911001001-P32911999999 50.8cc Backpack Power Blower
PB-500H (P02311001001 - P02311999999) Backpack Blower
PB-500H (P31312001001 - P31312999999) Backpack Blower
PB-500H (P31513001001 - P31513999999) Backpack Blower
PB-500H (P33011001001 - P33011999999) Backpack Blower
PB-500 (P02837001001-P02837002000) Blower
PB-500 (P02837002001-P02837999999) Blower
PB-500H (P02311001001 - P02311999999) Backpack Blower
PB-500H (P31312001001 - P31312999999) Backpack Blower
PB-500H (P31513001001 - P31513999999) Backpack Blower
PB-500H (P33011001001 - P33011999999) Backpack Blower
PB-500 (P02837001001-P02837002000) Blower
PB-500 (P02837002001-P02837999999) Blower
Shindaiwa
Products Compatibility
This item works with the following types of products:
- • Blower
Questions & Answers for Gasket-intake
No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
Tool Type:
Blower
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
, T-25 Torx bit for everything.
Only ran while modulating choke
I began by removing the plastic cage around the engine in the rear which is held in place by T-25 Torx screws and the air cleaner which is held in place by thumb screws. Once the cover is removed I removed the filter for inspection/replacement and behind it there are (2) phillips screws and (2) T-25 torx screws. I removed the (2) torx as these hold the back of the air box and carb. in place. The screws were around 3+" in length and once removed with air box rear I was able to access the (2) fuel lines for disconnecting very easily. Mine were somewhat brittle and I cut about an 1/8th" off in order to get back to more pliable line with easily enough left for reconnecting. The throttle cable was able to be disconnected with needle nose pliers from the carb. easily enough. I attempted to remove the reed valve behind this assembly however it was stuck in place pretty good and i did not want to break it just to replace a gasket which probably doesn't need replacing anyway so I skipped this. I installed the new carb. and all associated gaskets including rubber bushings and reassembled. I primed the carb. with the bulb a little more than usual until I felt fuel filling it up to ensure fuel had made it's way through the carb. set it to full choke full throttle and it started on the second pull! Runs like a champ again.
Thanks for being so reasonably priced!
Thanks for being so reasonably priced!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Product Information