Drive Belt 34-674
Part Number: 34-674
Order within the next 8 hours
and your part ships today!
and your part ships today!
Product Information
Description:
| This is a genuine Delta replacement part. Package includes one belt designed for easy installation. Clean the pulleys off before putting the new belt on to ensure top performance and longevity with your new belt. Inspect belts periodically and replace when worn to maintain peak performance. |
Frequently Purchased With
Compatibility
This part is compatible with the following machines:
the 14 compatible machines
Products Compatibility
This item works with the following types of products:
- • Saw
- • Table Saw
Questions & Answers for Drive Belt
No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
9 of 9 people found this instruction helpful
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver
Old Belt was slipping until saw would hardly cut.
Turn table saw upside down. Use angle setting to raise the end with the plastic cover that covers the belt. Use phillips screwdriver to remove four screws of cover. On the motor shaft there is a small cover held in position with 1 phillips screw. Remove it - might need to wrap shaft and hold it with pliers to remove screw. Remove old belt. New belt will be tight but I was able to push it on and turn the shaft until it worked its way all the way on. Replace the cover on the motor shaft by installing and lighting the phillips screw. Replace the plastic cover (4 screws) and turn the saw upright..
Did you find this story helpful?
Thanks for voting and helping fellow customers!
4 of 4 people found this instruction helpful
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Socket set, Wrench Set
Belt was torn.
I removed the saw stand, then turned the saw over. I removed the black cover at the end of the motor, and removed the old belt and cleaned out the area. I then started working the new belt on the shaft and pulley, starting on the edges, then while rotating the belt, pushing it onto the shaft and pulley all the way.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 3 people found this instruction helpful
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers
All the teeth on the belt were missing after owning this machine for 16 years.
It was extremely helpful that someone else had provided really good instructions. My only addition would be to take the base off the saw and turn it upside down on a low stool.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers
Drive belt was old and slipping
Followed machine instructions
Lowered blade
Removed blade cover
Angled blade to a 45 degrees
Turned table upside down
Removed 4 phillips screws on belt cover and removed cover
Slipped off old belt and worked new belt onto gears for blade and motor
Put belt cover back on
Turn table saw back upright
Put blade guard back on and adjusted blade angle to 0, plugged in and it worked
Lowered blade
Removed blade cover
Angled blade to a 45 degrees
Turned table upside down
Removed 4 phillips screws on belt cover and removed cover
Slipped off old belt and worked new belt onto gears for blade and motor
Put belt cover back on
Turn table saw back upright
Put blade guard back on and adjusted blade angle to 0, plugged in and it worked
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Socket set, Wrench Set
Table saw belt broke
1. Had to remove table saw from stand, turned it upside down in order to gain access to the housing for the belt.
2. Removed the belt cover, removed the old belt and cleaned the area.
3. Installed the belt on the edge of the shaft and pulley, and pushed on the belt as I turned it
2. Removed the belt cover, removed the old belt and cleaned the area.
3. Installed the belt on the edge of the shaft and pulley, and pushed on the belt as I turned it
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Table Saw
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Drive belt broke and brushes were bad
I removed the three screws on the drive belt cover.
I removed the one screw that holds the drive belt in.
Placed new belt onto the pulleys.
I put the one screw back in place that holds the drive belt on.
I put the drive belt cover back on and then I put the three screws back in.
I took out the brush cover caps that hold the brushes in.
I took out the old brushes and put the new brushes in.
I put the brush cover caps back on.
I removed the one screw that holds the drive belt in.
Placed new belt onto the pulleys.
I put the one screw back in place that holds the drive belt on.
I put the drive belt cover back on and then I put the three screws back in.
I took out the brush cover caps that hold the brushes in.
I took out the old brushes and put the new brushes in.
I put the brush cover caps back on.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 3 people found this instruction helpful
Tool Type:
Table Saw
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Socket set, Wrench Set
Belt was worn and teeth were tearing off, cover was cracked and chipped. I also replaced brushes at this time which I already had.
Unplug saw and remove blade. Vac and blowgun saw dust. Turn saw over, remove bottom half of base. Remove motor, leave electrical intact, no need to take motor to bench. Remove belt cover. Remove belt retainer washer and belt. Make sure pulleys are clean. Replace belt, washer and cover. I use a small drop of blue Loctite on all screws and bolts. If replacing brushes, unscrew brush covers and pull out old brushes. Look at armature with flashlight while turning and check for damage. Replace brushes and covers. Clean motor mount and install motor. Make sure mating surfaces and alignments pins are clean and burr-free. Replace base, turn saw over, install blade and check alignment. Plug in saw, cut wood.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Belt was broke on the table saw
Unscrewed cover plate that houses the belt put a new one on, just fed it on the pulley and replaced cover
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver
Drive belt on table saw broke.
Took the cover off the belt housing changed belt put housing cover back on went back to cutting wood
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Wrench Set, Hammer and pully puller
Armature shorted out
1. Removed the motor
2. Disassembled the motor
3. Installed new parts
4. Reassembled and reinstalled the motor
5. Repair complete
2. Disassembled the motor
3. Installed new parts
4. Reassembled and reinstalled the motor
5. Repair complete
Did you find this story helpful?
Thanks for voting and helping fellow customers!
show more
Reviews
9 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
7
4 stars
1
3 stars
0
2 stars
0
1 stars
1
< PREV
- 1
Successful repair by a novice
The drive belt in my Delta table saw broke and, not knowing much about this kind of machinery, I was afraid I would have to send it out for repair. But the local repair place couldn't get to my saw for at least six weeks, so I decided to see what I could do myself. After watching a You Tube video (everything imaginable is out there) I was able to get at the motor casing and uncover the broken belt. I easily found the required belt at Replacement Parts and it arrived in a few days. My lack of experience meant that mounting the new belt took me longer than a more savvy craftsman would take, but I got it mounted and my saw is back in operation. I learned a valuable lesson about what is possible with time, even by a novice. Thank you Replacement Parts and You Tube. John Long
Guest -
June 13, 2020
Verified Purchase
The belt arrived
It fit like a glove. It is in place, Very satisfied with it. Regards N. Roberts.
Guest -
May 28, 2020
Verified Purchase
BELT
I did it!! Hurrah! I loved getting my saw back to work! Thanks for the technical support.
Guest -
May 6, 2020
Verified Purchase
Fast service
The replacement parts were easy to identify and order correctly. Shipping was much faster than I anticipated. Thank you very much.
Guest -
October 29, 2019
Verified Purchase
Worked as expected.
The belt fit the saw and my saw is working great.
Guest -
October 8, 2019
Verified Purchase
Drive Belt
Very pleased with the product. Thank you. Also the service was very pleasing.
iGlobal -
May 19, 2019
Verified Purchase
Drive belt replaced. Part fit perfect, runs great!
Shipped and delivered fast, with shipping info provided by email. Belt was not easily replaced, but mission accomplished.
Guest -
April 23, 2019
Verified Purchase
Easy repair
Always have the replacement parts I need.
David -
April 19, 2022
Verified Purchase
Cost of spares?
The item was received in good order, but VERY EXPENSIVE.
iGlobal -
November 23, 2019
Verified Purchase
Verified Purchase
eReplacementParts Team
< PREV
- 1
Product Information
