Dewalt Logo Label 395657-00

Description:

This is a standard Dewalt logo decal/label commonly used on electric drills/drivers. It is a genuine part that is supplied directly from original equipment manufacturer. If you want to keep your tool looking good like new, this authentic label can help you replace a damaged or lost logo. This label has an adhesive back for easy application. Includes one (1) decal per order.

Compatibility

This part is compatible with the following machines:

DeWALT

Expand the 150+ compatible machines

Products Compatibility

This item works with the following types of products:

• Cordless Drill
• Drill
• Hammer Drill
• Impact Driver
• Screwdriver

Repair Instructions: Submitted by Customers Like You

2 of 2 people found this instruction helpful

Tool Type:

Cordless Drill

Parts Used:

Dewalt Logo Label - 395657-00

Screw,base - 330019-00

Switch Paddle - 383844-00

Clamshell Set - 652045-00

Repair Difficulty:

Easy

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Torx screwdriver to be specific

Housing broken, Screws rusty, switch paddle gummy

Removed one half of assy. housing, cleaned that side of motor and installed that side of the housing. The removed other broken half and cleaned that side of motor. Installed other side of housing and paddle assy. Put new screws in and attached label. Ops. checked ok.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

1 of 1 people found this instruction helpful

Tool Type:

Hammer Drill

Parts Used:

Dewalt Logo Label - 395657-00

Clamshell Set - 620711-02SV

Nameplate - 645166-00

Repair Difficulty:

Medium

Time Spent Repairing:

30-60 minutes

Tools Used:

Screwdriver, Pliers

Broken clamshell case from difficult drilling.

Remove battery, then remove the screws holding the housing together. Take a picture so you know where all the part go inside. Replace internal parts of the drill, then screw the housing together. I also replaced the logo and nameplate on the new housings.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Cordless Drill

Parts Used:

Dewalt Logo Label - 395657-00

Clamshell Set - 383841-09

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

, Torx bit

Plastic housing cracked

Removed one case half at a time and replaced. Need a long torx tool for one screw.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Cordless Drill

Parts Used:

Dewalt Logo Label - 395657-00

Clamshell Set - 620711-02SV

Nameplate - 645165-00

Repair Difficulty:

Easy

Time Spent Repairing:

15-30 minutes

Tools Used:

, Torx Driver

After being dropped many times, the drills clamshells finally broke beyond repair.

1. Use torx driver to remove broken clamshell halves.
2. Install new clamshell halves.
3. Replace torx screws.
4. Stick replacement labels on new clamshell halves.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Cordless Drill

Parts Used:

Dewalt Logo Label - 395657-00

End Cap - 620747-00

Clamshell - 622858-02

Nameplate - 615864-00

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Screwdriver

Drill clam shell housing was broken

Removed the screws from the clam shell and replaced one-half at a time and replaced screws
Installed the new labels.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Cordless Drill

Parts Used:

Dewalt Logo Label - 395657-00

Clamshell Set - 620711-02SV

Nameplate - 645166-00

Repair Difficulty:

Medium

Time Spent Repairing:

15-30 minutes

Tools Used:

Screwdriver

Replaced broken clamshell

Be careful, drill can separate and small gears will fall out. Also the plastic direction slide
can fall out. Check which way the arrows point before you separate the drill. Best thing to do is take a picture when you have the the broken housings apart.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Impact Driver

Parts Used:

Dewalt Logo Label - 395657-00

Clamshell Set - 607981-04SV

Nameplate - N009838

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

Screwdriver

Rubber grips coming off clamshell

Remove the screws that hold the housings together. Remove one half of the housing. Take a picture of where the parts are located. Install all of the parts in the new housing, then screw the new housing back together.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Tool Type:

Cordless Drill

Parts Used:

Dewalt Logo Label - 395657-00

Clamshell Set - 383841-09

Repair Difficulty:

Easy

Time Spent Repairing:

Less than 15 minutes

Tools Used:

, Torx screwdriver

I dropped my drill and busted the housing. Thought I'd have to throw the whole thing away but was able to repair.

Removed old housing by removing 6 screws. Take a picture of where all the internal parts are located. Then installed new housing. It was easy. Parts fit perfectly.

Did you find this story helpful?

Thanks for voting and helping fellow customers!

Reviews

Average Rating (out of 5):

4 Reviews

Click to filter by ratings:

5 stars

4

4 stars

0

3 stars

0

2 stars

0

1 stars

0

Sort by:

Highest Rating
Most Recent

< PREV

1

NEXT >

Had what needed and fast shipping.

They have most all parts for the restoration

Guest - September 13, 2021 Verified Purchase

New 10 year old Drill

Ordered several parts to recondition my old Dewalt drill. Everything came quickly and fit perfectly. My drill looks and works like brand new.

Guest - July 13, 2021 Verified Purchase

exact replacement

Fast delivery,fit fine

Guest - November 25, 2020 Verified Purchase

As described.

I was redoing my drill , had to put new stickers on the clam shell and bought this one and the one on other side . The parts I buy from them are always nice and you usually find what you need even if other places dont have it . I've been buying from them for a long time and I've only had a problem with two parts. One was a piece bent on a clam shell which was probably done when it was made and they replaced it with no problem even reimbursing me for the stickers I had already put on . And two , a shaft wouldnt fit on a drill even though it showed to be right , they promptly sent me a new one and it still wouldnt fit probably something with manufacturer and I was refunded promptly . Not bad for quite a few years.

Guest - August 13, 2019 Verified Purchase

Verified Purchase

eReplacementParts Team

Sort by:

Highest Rating
Most Recent

< PREV

1

NEXT >

Questions & Answers for Dewalt Logo Label