Carburetor 308028007
Part Number: 308028007
Order within the next 12 hours
and your part ships today!
and your part ships today!
Product Information
Description:
Genuine Homelite replacement part, this item is sold individually. A carburetor basically consists of an open pipe through which the air passes into the inlet manifold of the engine. The pipe is in the form of a Venturi: it narrows in section and then widens again, causing the airflow to increase in speed in the narrowest part. Below the Venturi is a butterfly valve called the throttle valve — a rotating disc that can be turned end-on to the airflow, so as to hardly restrict the flow at all, or can be rotated so that it (almost) completely blocks the flow of air. This valve controls the flow of air through the carburetor throat and thus the quantity of air/fuel mixture the system will deliver, thereby regulating engine power and speed. The throttle is connected, usually through a cable or a mechanical linkage of rods and joints. Fuel is introduced into the air stream through small holes at the narrowest part of the Venturi and at other places where pressure will be lowered when not running on full throttle. |
Frequently Purchased With
Compatibility
This part is compatible with the following machines:
Products Compatibility
This item works with the following types of products:
- • Blower
Questions & Answers for Carburetor
No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
14 of 17 people found this instruction helpful
Tool Type:
Blower
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers, Socket set
Had to replace the carburetor , carburetor gasket and replaced the throttle lever
It was fairly easy to replace the carburetor , gasket and the throttle lever. You just use a socket and a wrench to unscrew a couple of nuts and take both fuel lines off and take old carburetor off and replace with new carburetor and gasket and pull off old throttle lever and replace with the new one. Thanks
Did you find this story helpful?
Thanks for voting and helping fellow customers!
10 of 11 people found this instruction helpful
Tool Type:
Blower
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Socket set, Nutdriver
Needed a new carb
Make note of choke knob position and fuel lines for reassembly. Remove fuel lines at carb and choke selector knob. Remove 2 carb mount bolts, one is a socket, the other a torx. Pull carb, position new washer by lining up holes and then reassemble in reverse order.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 3 people found this instruction helpful
Tool Type:
Blower
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Nutdriver
Only run with a choke on.
Replaced the carburetor, now runs like it should.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 4 people found this instruction helpful
Tool Type:
Blower
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Socket set, Star bit.
Leaking diaphragm in carb.
Just a simple replace of the carburetor.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
4 of 6 people found this instruction helpful
Tool Type:
Blower
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Wrench Set, Adjustable Wrench
Carburetor not working
I removed the airbox, removed the fuel lines, disconnected the throttle cable. Installed new carb and reassembled. I also needed a fuel cap, so I just screwed that on.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Blower
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Nutdriver, Adjustable Wrench
wouldnt run unless on choke
removed air cleaner housing, r&r carb
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Blower
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Wrench Set
Faulty carburetor.
Removed the old carburetor and installed the new one.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Blower
Repair Difficulty:
Medium
Time Spent Repairing:
1-2 hours
Tools Used:
Screwdriver, Pliers, Socket set, Nutdriver
Blower is older and sat several months and would not start even after draining old gas and adding fresh.
Plug was ok and wire ok. Figured carb was plugged up. Just easier to try new carb. New carb and gasket with shipping about $35.
Replaced carb and gasket. Filled with fresh gas. Blower started on 2 - 3 pulls.
Replaced carb and gasket. Filled with fresh gas. Blower started on 2 - 3 pulls.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Blower
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Socket set, Nutdriver
Gas leak
Removed the fuel tank & Carburetor. Installed the new parts including a new carburetor to manifold gasket. Leaf blower is safe to use again.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Blower
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers, Nutdriver
Wouldn't run
Removed the fuel lines and the throttle
Remove the screws that are securing the carburetor and remove it and the air box
Install the air box and the new carburetor on the screws and screw them in
Install the throttle and the fuel lines
Remove the screws that are securing the carburetor and remove it and the air box
Install the air box and the new carburetor on the screws and screw them in
Install the throttle and the fuel lines
Did you find this story helpful?
Thanks for voting and helping fellow customers!
show more
Reviews
3 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
3
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
perfect fit
great job part arrived quickly and was perfect fit and is running great good job thank you
Guest -
July 19, 2020
Verified Purchase
Replacement part works great
Replacement part was the exact match,very easy to swap out.service, delivery, and quality of the product was awesome!! Thank you!!
Guest -
September 9, 2019
Verified Purchase
Great service.
The parts I ordered were as pictured and described, fit correctly, and were shipped promptly. Very happy with the service. Would not hesitate to order from them again.
Guest -
August 26, 2019
Verified Purchase
Verified Purchase
eReplacementParts Team
< PREV
- 1
Product Information