Repair Parts Home    Grill Parts    Char-Broil Parts    80013421 Burner w/Spider Guards (15-7/8")

Burner w/Spider Guards (15-7/8")

Part Number: 80013421
Char-Broil
Availability: 25+ in stock
Price: $8.61
Quantity:
Ships within 1 business day

*This part replaces obsolete part #: and 80005703.

Description:
This is a genuine Char-Broil replacement part. it is sold individually.
The burners are the part of the grill that the flame rises from.
The Burners flame is controlled by the control knobs that are attached to the Valve/Manifold/Regulator.
It is a good idea to keep these clean and covered as they have a tendency to rust and corrode.
Repair Stories
1 of 1 people found this instruction helpful
Tool Type:
Outdoor Grill
Parts Used:
Carryover Tube - 80005592
Burner w/Spider Guards (15-7/8") - 80013421
Grease Tray - G516-6900-W1
Flame Tamer - G501-0008-W1
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Pliers, Power Drill, Hammer, rust remover
Parts were rusted out
The most difficult part was removing the old rusted out parts and screws. The screws were corroded so bad it was there wasn't really a place to insert the screwdriver. Using rust remover/ bolt loosener and needle nosed pliers, work solution down into screw grooves until screw spins freely. Remove screws but save them. Not all of the new screws fit in the existing holes. Be sure to remove the screws that attach the igniter from the igniter burner before trying to pull out the igniter burner (there are 2). After screws are removed parts easily pull out or lift off. New parts were not an exact fit but we're better quality and we're close enough to make it work. Attach the igniter back onto the new igniter burner before trying to attach anything else (reuse of old screw school was necessary here). Lay in all burners and carry over tubes, insert screws but do not tighten all the way. After everything aligns tighten each screw most but not all of the way. Then go back and tighten them all the way. Other wise it is difficult to align the last screw. Also, be sure all of the carry over tubes face the same and correct direction.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Discussion
Discussion for Burner w/Spider Guards (15-7/8") - ( 80013421 )
You need to be signed in to participate in the discussion.
You need to be signed in to particupate in the discussion.
Ask a question, answer a question, or post a comment!
  • Subject:
  •  
  • Comment:
  •  
caguas1971
Question: Char-Broil Burner

caguas1971

The Burner w/Spider Guards (14-3/8") - ( 80013421 )
is in Stainless steel or regular steel?
WJA
Reply: Char-Broil Burner

WJA

Hello caguas1971,

I had someone check our stock of 80013421 and they are definitely made of stainless steel.

-WJA
Product Information
Manufacturer: Char-Broil
Category Number: 80013421
Classification: Part
Weight: 0.51 lbs.
Shipping: Ships Worldwide world wide shipping icon
Repair Guides
Articles:
Quick Fix: How to Replace the Handle on a Gas Grill
Have a rusty, old, or damaged handle on your gas grill that needs replacing? Follow the steps outlined below to replace...
November 15, 2012
Quick Fix: How to Replace the Burners on a Char-Broil Tru-Infrared Gas Grill
Learn to replace the burners on your Char-Broil grill in a matter of minutes. ...
November 14, 2012
fancyboxy