eReplacementParts.com
877-346-4815
DeWALT Parts
Repair Parts Home  Power Tool Parts  DeWALT Parts  N093746 Carbon Brush And Holder

Install
Videos!
Grid squares measure 1x1 inch

Carbon Brush And Holder N093746

Part Number: N093746
DeWALT
Availability: In Stock
Price: $11.70
Order within the next 3 hours
and your part ships today!

*This part replaces obsolete part #: N039820 and N039819.

Product Information
Description:
This is a genuine DeWalt replacement part, sold individually. Includes 2 brushes and holder.

Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned.

It is recommended to take note of how the wire leads connect to the assembly, and reconnect the same way.

Compatible with the tools listed below.
Frequently Purchased With
Products Compatibility

This item works with the following types of products:

  • • Impact Driver
  • • Impact Wrench
Repair Guides
Watch the Repair Video for Carbon Brush And Holder

Questions & Answers for Carbon Brush And Holder


No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
12 of 12 people found this instruction helpful
Tool Type:
Impact Driver
Parts Used:
Carbon Brush And Holder - N093746
Steel Ball - N089668
Sleeve - N078437
Compression Spring - N019351
Hog Ring - N053863
Plain Washer - N016823
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
, torx #10, small screw driver
We use the DeWalts for continuous use. We wear them out.
Pull the case apart disconnect wires from brush assy, replace brush assy attach wires.
Pop the C clip remove the washer, sleeve and spring. The ball is gone by now. replace ball, spring, washer and C clip. I take the opportunity while appart to clean the inside of the case of old dirt and grease. I re grease the gear assy in the nose cone.

Did you find this story helpful?
Thanks for voting and helping fellow customers!
6 of 7 people found this instruction helpful
Tool Type:
Impact Driver
Parts Used:
Carbon Brush And Holder - N093746
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Socket set, Nutdriver
Brush assembly broke
1 Split Case
2. Removed broken brush assembly
3. Installed new Brush assembly
4. Put Case back togeather
Did you find this story helpful?
Thanks for voting and helping fellow customers!
3 of 3 people found this instruction helpful
Tool Type:
Impact Driver
Parts Used:
Carbon Brush And Holder - N093746
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Sparking and smoking from Impact Driver
Removed the seven screws on the one side of the impact driver.
Carefully pried up on cover.
Disconnected the two wire leads to brush and holder assembly.
Carefully pried up on impact and brush assembly at the same time together.
Slide off brush and holder assembly and hold open new copper brushes and slide over armature and reverse steps on reassembly.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Impact Driver
Parts Used:
Carbon Brush And Holder - N093746
Light Ring Assembly - N073422
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers
My driver had lost power and was heating up
1. Remove all screws from the body of the driver
2. Remove one side cover from the driver.
3. Remove motor/ transmission an brush assembly as one unit. Note alignment of electric motor parts.
4. Unplug remove old brush assembly and reinstall new brush assembly.
4a. If ou are replacing the light ring, now is the time to unplug and remove and replace it.
5. Put brush assembly, motor and transmission together and put back into body of driver.
6.Put other side of driver on and reinstall screws.
Put battery in and test the fix.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Impact Driver
Parts Used:
Carbon Brush And Holder - N093746
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Nutdriver, Torx driver
One of the Brushes got stuck
Dropped impact in the mud than the motor started sparking when you press the trigger so thought motor was bad replaced brushes now it works like brand new
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Impact Wrench
Parts Used:
Carbon Brush And Holder - N093746
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Torx driver
Losing power
Remove cover and replace carbon brush
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Impact Driver
Parts Used:
Carbon Brush And Holder - N093746
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Torx driver
Brushes worn out
Remove screws from clam shell assy. and separate, remove motor and impact assy. Separate motor from impact drive and clean all parts. Unplug brush assy. and replace with new one. Resurfaced commutator and reinstalled motor and impact assy. Reinstall clam shell install battery and get back to work!!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Impact Driver
Parts Used:
Carbon Brush And Holder - N093746
Magnet Ring - N309481
Armature Assembly - N268382
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Impact drill would not turn.
1. Take the screws out.
2. Pry the two halves apart.
3. Pull the wires off the brush holder. Note which color wire goes where.
4. Disconnect the wires for the lights.
5. Pull the brush holder, ring, armature, and gear housing out but note how the ring is sitting in the housing.
6. Install the new ring, brush holder, and armature.
7. Install the ring in the same orientation as the old magnet ring.
8. Connect the lights
9. Connect the wires the the brush holder.
10. Put the two halves back together.
11. Put the screws back in and tighten.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Impact Driver
Parts Used:
Carbon Brush And Holder - N093746
Switch Assembly - N359999
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
, Torx bit
Switch was bad
1. Took case apart
2. Removed both switch and brush set
3. Reinstalled new switch and brush set
4 Reassembled case
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Impact Driver
Parts Used:
Carbon Brush And Holder - N093746
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Brushes went bad
Take out all the screws, I believe it was a t-10 or t-15 star bit, pull apart plastic casing without disassembling the inner parts, take out old brush and holder assembly and install new bushes and holder, make sure everything goes back together the same way you took it apart and make sure the forward reverse switch is still in the right position and it's wire is not in a pinch zone then put the plastic case back together and put screws in, test drill out
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
4.7
Average Rating (out of 5):
7 Reviews
Click to filter by ratings:
5 stars
6
4 stars
0
3 stars
1
2 stars
0
1 stars
0
  • Highest Rating
  • Most Recent
< PREV
  • 1
NEXT >
  • The suggested part was the fix and easy to install.
    A small suggested part saved me from buying another expensive tool.
    Lawton - July 26, 2023 Verified Purchase
    You always have the right parts
    prefect fit. Great parts fast shipping. Never had a problem with parts from you. Thanks Jim
    Jim - November 4, 2020 Verified Purchase
    Looks and works perfect
    This is a great prized unit and it was shipped fast. Its cheaper to build my unit with the parts yall carry than to buy a new one.
    Kenny - November 11, 2019 Verified Purchase
    Easy Repair,
    arrived on time and in good condition , and everything working again.
    iGlobal - September 12, 2019 Verified Purchase
    saved me money from having to buy new 20 volt inpack
    received very quick . exact what i ordered
    Guest - August 12, 2019 Verified Purchase
    Easy fix.
    Easy replacement and it’s like having a new impact again. Just make sure you don’t mix up it will run opposite to the switch.
    Guest - July 30, 2019 Verified Purchase
    Great part, terrable service
    This was a factory DeWalt part and it was excellent. However the parts took over 1 1/2 weeks to arrive and that is not acceptable. I had to call and was told the parts were ready to be shipped but were sitting on a pallet. This and other parts were to repair customer's tools and my customers were getting upset over the slow service which reflects badly on me. There are many other places to purchase parts and unless I am assured this will not happen again I will buy my parts elsewhere.
    Guest - October 30, 2019 Verified Purchase
    Verified Purchase
    eReplacementParts Team
    • Highest Rating
    • Most Recent
    < PREV
    • 1
    NEXT >
    Product Information
    Repair Guides
    Watch the Repair Video for Carbon Brush And Holder
    eReplacementParts.com
    7174 South 400 West
    Suite 5
    Midvale, UT 84047
    visa mastercard discover american express PayPal