Repair Parts Home Appliance Parts Breville Parts Breville Espresso Machine Parts
Breville 800ESXL Die-Cast Espresso Machine Parts
Discussion for the Breville 800ESXL Die-Cast Espresso Machine
Post a Comment
Ask a question, answer a question, or post a comment!
Question: Breville 800ESXL
My machine will not turn on when I push the button. Per the internet, the problem is the Zener Diode ZD-6. I bought the diode shown in the parts list, but it looks like it is D6. I think the solution is to buy the entire circuit board, but I do not see it in your parts list. Where can I get one?
Reply: Breville 800ESXL
The best solution is to replace the Main PCB Assembly #800ESXL/232. Replacing the whole board should fix your problem.
Question: Part Discontinue
This expresso machine is 1 year three months old and the 800ESXL/242 part is no longer available. This is the part that is broke and causing machine to leak. I can not afford to replace this entire unit
Reply: Part Discontinue
Unfortunately, this part is really discontinued without a substitute.
Question: 800ESXL Pump Replacement
When I turn on the machine, it just sits there doing nothing. The pump is shot, I think, and I'm not sure how to replace it, any suggestions greatly appreciated.
Reply: 800ESXL Pump Replacement
Sometimes this type of a repair can get rather involved. You might try taking your machine to a local Breville Authorized Service Center.
Hope this helps,
Question: Leaking At Swivel Head Of Steam ...
It appears that the silicone washer may be the cause of the leaks at the swivel on my machine. This part is shown as discontinued. is there an equivalent part or must I replace the entire wand assembly?
Are there instructions for replacement of the seal and/or the wand?
Question: No Steam And Machine Won't Rehea...
The machine will not put out any steam, just little drops of water although you can hear the pump running. Also, it will put out very hot water but after a few seconds the hot water is not hot anymore, just warm. Is the problem electronic, thermostats? It appears the water heater and pump are working, but there seems to not be continuous heat for hot water or 'extra hot' heat needed for steam. Any help would be appreciated.
Reply: No Steam And Machine Won't Rehea...
Hello, my machine doesn't heat up anymore. Did you make the repairs on your machine?
Question: Leaks Water Out Of The Diffuser ...
I hope someone could help me! The moment I turn on the machine there is water running out of the Diffuser (part #124) I believe that this part is connected to the Thermal Block Assembly (Part #251) I have a few options, or the Thermal Block has past away, or a whole in the diffuser so the pressure is dropped and water leaks. Anyway, suggestions ideas are more then welcome. Greets Coffee Gwen A.K.A
Question: Disassembly Instructions
I would like to disassemble the appliance to access the tubes that go between the pump and the tank, boiler, etc. What is the easiest way to accomplish this?
Reply: Disassembly Instructions
I am trying to disassemble to get at the Thermoblock. I have removed plastic sleeve screws under the brew head, and the brewhead housing screws, and the bottom of unit screws and removed the drip pan. The dang thing doesn't want to open up. I can't see what I am missing. Any ideas?
Reply: Disassembly Instructions
Remove both part #105 Top Connectors with a screwdriver. Use a soft hammer to tap the top cover toward the front of the machine about 1/4 inch. The top cover should lift straight up.
Question: Screw 4 X 10 - ( 800ESXL/209 )
is there a cross reference for this screw that is no longer availble?
Reply: Screw 4 X 10 - ( 800ESXL/209 )
The manufacture has not replaced the old part number with a new one. Your best bet would be to locate a local nut & bolt store in your area that will be able to sell you a 4mm x 10mm screw that would work in your espresso machine.
Question: Water Leak
when I make coffee, water leaks out of the holes by the silicon seal. I changed the seal and still leaks. can you help?
Reply: Water Leak
Probably the Water Valve assembly its plastic and easily cracks if you changes the seals already the valve is probably cracked.
Question: BREVILLE ESXL
MY MACHINE HAS NO POWER GOING TO IT AT ALL. DOES THIS MACHINE HAVE A CIRCUIT BOARD TO REPLACE?
Reply: BREVILLE ESXL
Yes this machine does have a circuit board and it may need to be replaced.
While making an espresso, for no apparent reason, the pump stopped pumping coffee. It still had water in water tank. Do I have to change the pump or is there a protection mechanism that prevents the pump from breaking? My email is link removed.
Bonjour,je ne sais pas si vous avez eu des r%uFFFDponces a vos questions mais il semnble qu'il m'arrive la meme chose,on entend la pompe mais rien ne se passe.j'ai defait la machine et la pompe tourne mais ne pompe tout simplement pas.Si vous avez eu des r%uFFFDponce SVP donnez moi des nouvelles
[Hello, I do not know if you have had your questions responded to, but the same thing happens to me, means the pump but nothing happens. I undid the machine and the pump runs but does not pump just pauses. If you had a reply Please give me news
You need to physically take apart the machine and see if the pump is working. If it is sucking and nothing comes out of it, then the pump mechanism is the problem. The tube is see through when you take it apart so you should be able to tell if it's being pushed out.