Call us toll free 6:30 to 5, Mon-Fri, mst 866-802-6383

Shop All
Departments

Appliance Parts

Exercise Equipment Parts

GPS Parts

Grill Parts

HVAC Parts

Home Office Parts

Lawn Equipment Parts

Motorsport Parts

Plumbing Parts

Power Tool Parts

Restaurant Equipment Parts

Vacuum Parts

Bosch 18636 (3601J13110) 36V Bosch Brute Tough&trade 1/2" Hammer Drill/Driver Parts

Page A

Download Diagram

Fig #	Part #	Img	Part Name	Availability	Price	Qty
1	2605105089		Housing	Ships in 4 - 7 business days	$21.62
4	1607233279		Switch Assembly	Ships in 4 - 7 business days	$100.00
5	2601099149		Adjusting Slide	Ships in 4 - 7 business days	$1.10
11	2600508056		Cover	Ships in 4 - 7 business days	$2.48
12	2600508057		Cover	Ships in 4 - 7 business days	$2.48
32	2601099152		Adjusting Slide	Ships in 4 - 7 business days	$6.44
61	2608040190		Support	Ships in 4 - 7 business days	$4.84
70	2605190571		Push Button	Ships in 4 - 7 business days	$1.32
71	2604610104		Spring	Ships in 4 - 7 business days	$0.66
91	2607336007		Battery	Ships in 4 - 7 business days	$132.50
91	2607336009		Battery	Ships in 4 - 7 business days	$213.00
101	2603490018		Screw	Ships in 4 - 7 business days	$0.66
107	2603421229		Torx Flat Head Screw	Ships in 4 - 7 business days	$1.10
653	2607225105		Charger	Ships in 4 - 7 business days	$97.90
655	2602025126		Auxiliary Handle	Ships in 4 - 7 business days	$8.58
Fig #	Part #	Img	Part Name	Availability	Price
802	2607022836		DC Motor	Ships in 4 - 7 business days	$97.90
809	2601115377		Label	Ships in 4 - 7 business days	$2.48
816	2607034904		Carbon Brush Set	Ships in 4 - 7 business days	$8.58
820	2601115375		Label	Ships in 4 - 7 business days	$2.48
821	2601115378		Nameplate	Ships in 4 - 7 business days	$2.48
822	2601115411		Label	Ships in 4 - 7 business days	$2.48
823	2601115412		Label	Ships in 4 - 7 business days	$2.48
825	2608572903		Keyless Chuck	In stock 4 available	$51.98
845	2606200948		Drive Assembly	Ships in 4 - 7 business days	$100.00

Drill Parts

Hammer Drill Parts

Discuss

Repair Videos

Articles

Popular Parts

Carbon Brush Set $8.58	Torx Flat Head Screw $1.10
Keyless Chuck $51.98	Screw $0.66
Adjusting Slide $1.10	DC Motor $97.90
Switch Assembly $100.00	Auxiliary Handle $8.58

Repair Videos

How to Remove a Drill Chuck

How to Remove a Stuck Drill Chuck

Repair Articles

How to Remove a Stuck Drill Chuck
Broken gearboxes and sticky chuck screws can make removing a drill chuck difficult. This article explains the tricks you need to overcome these common repair setbacks.

Drilling, Fastening, and Hammering Power Tools
This article lists the major categories of drilling, fastening, and hammering tools, and explains the basic applications, types, and features of each.

How to Remove a Drill Chuck
This article explains steps for how to remove threaded-on chucks and taper-fit drill chucks, as well as steps for removing a spindle from an open-center chuck.

Power Tool Care and Maintenance 101
This article suggests guidelines for power tool care and maintenance. It also describes information tools available at eReplacementParts.com.

Discussion

Discussion for the Bosch 18636 (3601J13110) 36V Bosch Brute Tough&trade 1/2" Hammer Drill/Driver

Post a Comment

[ Ask Question | Add Review ]

Ask a question, answer a question, or post a comment!

Question: Bosch 18636 Thanks

paico

will the switch assembly cause the drill to act as if the drill has a dead battery when the batteries are fully charged or is there another problem with this drill we have only used this drill a few times but it quit in the middle of a job the barreries test good

thanks

Question: Bosch GBH10 DC

Graham

Have purchased GBH10 dc with a broken connecting rod. I purchased a new rod. While using it for the first time, the connecting rod has again broken. There is no obvious damage internally. The piston appears to move freely on the bench. Any advise you can offer would be appreciated. Kind Regards, Graham

Question: Chuck

I'm repairing a Bosch 18636 and I'm having problems removing the chuck. Any advise?

Reply: Chuck

zero

The chuck has a torx headed left hand threaded flat head machine screw in the end. After you remove this machine screw put a big allen wrench in the chuck jaws for leverage and the chuck unscrews from the end of the drill (right hand threads). It is pretty simple.