Nt Srv Asm Blower Wheel 668n W S85600000
Part Number: S85600000
Order within the next 8 hours
and your part ships today!
and your part ships today!
*This part replaces obsolete part #: S85600000B, 85600000B and 85600000.
Product Information
Description:
| The wheel goes next to the fan motor and the motor mount. This item is sold individually and is made out of plastic. This is an authentic Broan and Nutone replacement part that is sourced from the original manufacturer for use with ceiling heaters and exhaust fans. A screwdriver and a socket set may be needed during the replacement of this part. It will need to be replaced if it breaks. |
Frequently Purchased With
Compatibility
the 22 compatible machines
This part is compatible with the following machines:
Nutone
665 Ceiling Heater
9417 Ceiling Heater
9417D Ceiling Heater
9417DN Ceiling Heater
9427 Ceiling Heater
9427P Ceiling Heater
9417 Ceiling Heater
9417D Ceiling Heater
9417DN Ceiling Heater
9427 Ceiling Heater
9427P Ceiling Heater
VH9417 Ceiling Heater
VH9417D Ceiling Heater
VH9427P Ceiling Heater
668N Exhaust Fan
665N Heat-A-Ventlite Heater
VH9417D Ceiling Heater
VH9427P Ceiling Heater
668N Exhaust Fan
665N Heat-A-Ventlite Heater
Broan
Products Compatibility
This item works with the following types of products:
- • Heater
Questions & Answers for Nt Srv Asm Blower Wheel 668n W
No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
Tool Type:
Ventilation
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Socket set
The motor on my exhaust fan died. A new light/exhaust fixture would have required a drywall patch. I didn’t want to mess with that.
1. With a small socket I took off the nuts and washers that held the mounting bracket on the old motor.
2. Placed the new motor in the old bracket and refastened the washers and nuts, being careful to put the ground wire back in place under one of the nuts.
3. Attached new fan wheel to the motor.
4. Gently maneuvered the fan wheel into the duct.
5. Mounted the bracket back in the housing, loosely tightened the mounting screws.
6. Made small corrections to the whole assembly until the wheel no longer struck any part of the duct.
7. Tightened screws from the mounting bracket.
8. Plugged in the motor.
9. Success!
I read several reviews that stated the cord was too short to reach the electrical outlet inside the fixture. I did not have that problem. I was very relieved.
2. Placed the new motor in the old bracket and refastened the washers and nuts, being careful to put the ground wire back in place under one of the nuts.
3. Attached new fan wheel to the motor.
4. Gently maneuvered the fan wheel into the duct.
5. Mounted the bracket back in the housing, loosely tightened the mounting screws.
6. Made small corrections to the whole assembly until the wheel no longer struck any part of the duct.
7. Tightened screws from the mounting bracket.
8. Plugged in the motor.
9. Success!
I read several reviews that stated the cord was too short to reach the electrical outlet inside the fixture. I did not have that problem. I was very relieved.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Ventilation
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
worn out fan motor
remove old fan motor and wheel and replace with new
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Ventilation
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Socket set
Excessive noise
Fan motor with wheel replaced.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Product Information
